Key facts
| What changes | What it does to the hull | What you notice |
|---|---|---|
| Liquid in a part-filled tank | Runs to the low side as the boat heels | Slower recovery and a longer roll |
| A cross-connected pair of tanks | Behaves as one common tank | More liquid moves for the same angle |
| Loose water in the bilge | Adds weight that can travel to leeward | The boat feels heavy on one side |
| Fish or fish product in the hold | Shifts like a liquid when it can flow | Trim changes during the day |
| A beam sea | Pushes the hull down the wave face | The roll deepens near the trough |
| Heel and immersion limits | Define the acceptable angle | The rail comes close to the water |
Same weight, different behaviour
The centre of gravity is the point where the hull's weight can be treated as acting. Its height depends on the distribution of everything aboard: fuel, water, engine, ice, gear, crew, the catch and the hull. Move a heavy box from the sole to a shelf and the centre of gravity rises, although the total weight is unchanged. A rise in the centre of gravity shortens the righting arm at any given angle and lengthens the roll period. A slow, easy roll can look comfortable while it is a sign that righting ability has been reduced. A list at rest, a boat that settles to one side as the wind shifts, or a trim that changes after the ice melts are clues that the load is not where the plan assumed. The measure that ties these observations together is the metacentric height, usually written GM. It is the distance between the hull's centre of gravity and its metacentre, the point about which the hull rotates at small angles. A larger GM means a stiffer boat with a short, snappy roll; a smaller GM means a tender boat with a long, easy roll. Too small a GM and the boat has little reserve before it takes on water; too large and the roll is violent enough to throw a crew member off a deck. GM is not a fixed property. It falls as weight is added high, and it falls as free surface develops. A boat that was stiff on the delivery trip can be tender on the fishing trip with the same displacement, because the loading and the tank states have changed.
The virtual rise from a free surface
46 CFR 28.540 names the mechanism directly: the virtual rise in the vessel's vertical centre of gravity due to liquids in tanks. The liquid has not moved the hull's actual centre of gravity upward. Instead, the free surface lets the liquid level remain horizontal as the boat heels, so the liquid's centre of gravity moves toward the low side. That shift adds a heeling moment, and the hull behaves as if its centre of gravity were higher. The regulation requires the effect to be included in stability calculations for each partially filled tank and hold containing a liquid that can shift. It also requires the maximum free surface effect of a tank, or a transverse pair of tanks, having the greatest free surface effect for each type of consumable liquid, plus a correction for service tanks. A full tank has little free surface because the liquid cannot form a long, level surface that moves across it. The dangerous condition sits in the middle, where a wide surface is free to travel. A part-filled fuel tank in a beam sea can therefore make a boat feel less stable than the same tank when full, even though the full tank weighs more. The size of the loss depends on the shape of the free surface, not its depth. A wide, shallow tank has a larger second moment of area than a narrow, deep one, so a broad tank half full is worse than a tall tank half full with the same volume. That is why subdivisions and baffles are fitted: they cut the free surface into smaller panels and reduce the travel of the liquid.
Cross-connected tanks
46 CFR 28.540 adds a rule that catches many crews: the free surface effect of tanks fitted with cross-connection piping must be calculated assuming the tanks are one common tank, unless valves that will be kept closed to prevent transfer as the vessel heels are installed in the piping. An open cross-connection turns two small free surfaces into one large one. Liquid can move from the windward tank to the leeward tank as the boat rolls, which is the shift the rule is trying to capture. Closing the valves changes the geometry, but only if they are actually closed and stay closed; a valve opened to trim the boat and left open returns the system to the common-tank case. The practical check is simple: know which valves are in the transfer line, whether the vessel's instructions require them closed for sea, and confirm their position before the weather builds. A hard-to-reach handle or faded label is a reason to trace the line, not guess.
Fish, loose water and the working deck
The rule does not stop at fuel and water. 46 CFR 28.540 also requires the free surface effect of each partially filled tank and hold containing a liquid that is not a consumable, or containing fish or a fish product that can shift as the vessel heels. It explicitly includes correction for loose water within the hull associated with processing fish. A fish hold is not a solid block. Fish in slush, meltwater and wash-down water can flow as the hull rolls, with the same virtual rise as a part-filled tank. Loose water in the bilge, processing water on deck and a blocked scupper add weight that travels to the low side. The boat may not list at the dock because the water is evenly spread; it lists once the roll starts. The bilge is a stability item, not just a housekeeping item. A dry bilge reduces the free liquid available to shift, while a bilge pumped only when the float switch trips may carry water at the worst moment. The same logic applies to fish bins, wash-down hoses and melting ice. Icing deserves a separate note in cold conditions. Spray that freezes on a mast, a radar arch or a pot hauler adds weight high above the deck, where it does the most damage to stability. A few centimetres of ice on a large area can weigh more than the crew, and it does not come off by itself. The remedy is to knock it off early and to slow down before the accumulation starts.
Beam seas and the roll
A beam sea pushes the hull sideways as the wave face passes. The hull heels, the free surface moves, and the righting moment has to overcome both the wave and the shifted liquid. If the centre of gravity is already high, or the free surface is large, the roll that follows is deeper and slower to stop. The dangerous combination is a beam sea with a period close to the boat's natural roll period. The roll can build over several cycles instead of settling after one; a crew that feels it deepening each time, with the rail closer to the water, is seeing resonance rather than one bad wave. Changing heading or speed changes the encounter period and can break the pattern, but the underlying margin is unchanged. A following sea brings a different failure. A wave that overtakes the hull can lift the stern, reduce steerage and push the bow into a yaw that the rudder cannot catch. The result is a broach, with the boat laid broadside to the next wave. Speed control is the tool: stay slightly ahead of the wave train or well behind it, and avoid the intermediate speed where the wave picks up the stern and the rudder has no authority.
Heel and immersion limits
Stability is not a feeling; it is assessed against defined heel and immersion limits. For small passenger vessels, 46 CFR Part 178 states that in no case may the angle of heel exceed 14 degrees, and it sets maximum allowable immersion for certain cockpit vessels. A fishing boat may fall under a different subchapter, but the principle is the same: the acceptable angle is a number in the vessel's stability information. Immersion limits matter because water can enter a cockpit, hatch or vent before the righting moment is exhausted. Once water is inside the hull and free to move, the stability calculation has changed in the wrong direction. Downflooding points are the openings that let that happen: hatches, vents, engine room intakes, cockpit drains that backflow, and the transom cut-out on a small outboard boat. A boat can have an acceptable righting curve and still be lost through an open hatch at fifteen degrees of heel. The crew's check is physical — are the hatches dogged, the vents clear and the scuppers open — not numerical. The crew's job is to stay inside those limits, not to calculate them. That means keeping heavy gear low and secured, the bilge and fish hold as dry as work allows, and treating a part-filled tank or open cross-connection as a known loss of margin. If the vessel carries a stability booklet, the limits in it are the reference; a rule of thumb from another boat is not.
Small boats and level flotation
An outboard boat under twenty feet is usually assessed against a different standard: level flotation, which is about staying afloat and upright after swamping rather than resisting a heel in a seaway. The capacity plate is the summary of that assessment, and it states the maximum weight, persons and horsepower the hull was tested with. The plate is a limit, not a target. A boat loaded to the plate with a full livewell, a cooler of ice and two extra crew is over the weight the flotation was designed for, and the reserve that keeps it level after a swamping is gone. Add a heavy four-stroke engine or a tower and the assumptions behind the plate have changed again.
Checks before the weather builds
Keep the bilge dry and pump before the weather builds, not after. Treat a part-filled wide tank as a stability reduction, especially in a beam sea. Close cross-connection valves when the vessel's instructions call for it, and confirm they stay closed. Secure fish and ice so that liquid cannot run across the hold. Read the heel and immersion limits in the vessel's stability information. Dog the hatches and clear the scuppers before the sea gets up. Knock ice off the rig before it accumulates.
Weight does not make a boat stable
Assuming a heavier boat is always a more stable boat. Leaving a cross-connection open because the boat trims faster that way. Pumping the bilge only when the float switch trips. Treating a slow, comfortable roll as a sign of stability. Loading to the capacity plate and then adding gear. Running a following sea at the speed where the stern is lifted. Section index: environment index.
Sources
- 46 CFR 28.540 — Free surface — U.S. Government, eCFR · T1
- 46 CFR Part 178 — Intact stability — U.S. Government, govinfo · T1
- 46 CFR Part 170 — Stability requirements for all inspected vessels — U.S. Government, eCFR · T1