Key facts
| Item | Referenced to | What you do with it |
|---|---|---|
| Charted depth | Chart datum, a low-water plane | Add the height of tide |
| Height of tide | Chart datum | Read from the tide table |
| Actual depth | Water surface at the time | Charted depth plus height |
| UK datum | Normally approximately Lowest Astronomical Tide | Confirm on the title block |
| Canadian datum | Lower low water, large tide (LLWLT) | Do not assume the UK value |
| Tide table time | National standard clock, or daylight saving | Convert to your working clock |
| Weather effect | Not in the astronomical prediction | Allow a margin for surge |
Chart datum sits below the printed depths
Get any one of them wrong and the depth under the keel is not the number the arithmetic produced. Both conversions are simple, and both are routinely skipped. Chart datum is the plane below which all depths on a navigational chart are published. It is not mean sea level, and it is not the level at which the water usually sits. It is a low reference plane, chosen so that most charted depths are positive and so that the numbers err on the side of showing less water than there is. Tidal heights are referred to the same plane. That is why the arithmetic works: the height of tide from the table and the charted depth from the chart share a zero, so adding them gives the actual depth. Mix a height from one frame with a depth from another and the sum is meaningless. In the United Kingdom the plane normally approximates Lowest Astronomical Tide: the floor produced by the astronomical factors alone when average weather is assumed. It is a conservative baseline rather than a forecast of today's low water. A spring low can approach it; an ordinary neap low usually sits well above it. The word "normally" carries weight. Chart datum is a property of each chart, and the title block or legend is the authority for that chart. A number copied from a neighbouring chart, or from another country, may not belong to the same plane.
The one-line depth check
Actual depth equals charted depth plus height of tide. A chart that shows 2.5 m at a mark, with 1.2 m of tide above chart datum at that moment, has about 3.7 m of water over it before allowance for waves, squat or a conservative under-keel margin. The check has three failure points. The first is a height that is not referenced to the same datum as the chart. The second is a height for a different location or a different time. The third is forgetting that the prediction excludes weather. The arithmetic is trivial; the errors are all in the inputs. Run the check on the shallowest point of the planned route, not the deepest. A route that clears a bar by two metres at the deepest sounding can still ground on the shoal patch that was not the focus of the plan. For an angler rather than a navigator, the same check applies to wading and anchoring. A mark that is dry at chart datum can be wadeable at a predicted height of 0.6 m, and a channel that shows 1.0 m on the chart can be too shallow for a boat at low water. The chart and the tide table answer different parts of the question, and neither answers the weather. Work the check from what the hull needs. A boat that draws 1.4 m needs 1.4 m of water to float and more to run: add 0.3 m for squat at speed and 0.5 m for swell and error, and the required depth is 2.2 m. On a sounding of 1.8 m the tide has to supply 0.4 m. Whether it holds that height long enough is the second question, because 0.4 m is passed twice on a small range and held for hours on a big one.
Datums are national, not universal
Canada uses a different plane from the United Kingdom. On most Canadian coastal charts the reference is lower low water, large tide, abbreviated LLWLT: the average of the lowest low waters of large tides over a long record. It is a low-water plane and it is conservative, but it is not the same numerical surface as Lowest Astronomical Tide. Both planes are computed from tide records with different criteria, different record lengths and different definitions of "large tide". A depth read from a Canadian chart and a height read from a British tide table are therefore not in the same frame unless someone has converted them. Adding the two numbers produces a figure that is neither a chart datum depth nor a true depth. The practical rule for a foreign trip is to use the chart's own datum note and the tide service published by the same national hydrographic office. Do not take a depth from one country's chart and a height from another country's app and add them. That is not a conversion; it is a category error. Where the chart's datum is not the one the tide service uses, most services publish a conversion or offer heights in more than one datum. Use the conversion rather than estimating the offset. A datum offset of a few tenths of a metre is the difference between crossing a bar and touching it.
Tide tables run on local clock time
The time column has the same problem in a different dimension. Tide predictions are published in the national standard time of the country, and services that cover a country observing daylight saving switch with the clocks. Australia is a clear case. The Bureau of Meteorology publishes predictions in daylight saving time when it is observed, which means the printed time changes by an hour twice a year while the tide itself does not. Anyone arriving from a country that does not change clocks, or reading a table on a phone that has already switched, can be an hour out without noticing. An hour is enough to put a boat on a bar at the wrong stage. Two hours, if a table is in a different standard meridian from the one you assume, is enough to make the whole plan meaningless before you leave the dock. Meridian offsets are not all whole hours. India runs on UTC+5:30 and Nepal on UTC+5:45, so a table read from a UTC source and applied on a local watch is half an hour or 45 minutes out before daylight saving enters the question. Near the date line the error moves the day as well: a high water at 00:20 in one zone is 23:20 on the previous date in the next, and a plan built on the wrong date is wrong at every mark on the route. The fix is procedural. Establish which time zone the table uses, whether daylight saving is in force on the date, and whether your phone, chartplotter and watch agree. Then write the departure time in the same clock you will use on the water, and keep it in one place.
Predictions are astronomy, not observation
A tide table is a calculation. It combines the astronomical forcing with a long record of local tides to produce heights and times for a standard port. It does not include the weather, and the weather is what moves the actual level away from the prediction. The Australian service publishes predictions for more than 380 locations around Australia, Antarctica and the South Pacific, and states plainly that weather effects are not included. That is not a limitation unique to Australia; it is how astronomical predictions work everywhere. The consequence for planning is a margin. On an exposed coast, a sustained onshore wind can raise the level by several tenths of a metre, and a deep low can add more. Offshore wind and high pressure do the opposite and can leave less water than predicted. A plan that uses the predicted height as an exact value has no room for either. Air pressure accounts for part of the gap. A change of 1 hPa moves the sea surface about 1 cm in the opposite direction, so a deep low standing 40 hPa below normal lifts the level roughly 0.4 m, and a strong high 20 hPa above normal takes about 0.2 m away. That is the same order as the tide height on a neap, which is why the pressure chart belongs beside the tide table on an exposed coast. The asymmetry between height and time is useful. Predicted times are usually close to observed times, while predicted heights can be off by a noticeable margin. If a table's heights disagree with the water but its times look right, the cause is weather, not a broken table.
Two checks before a foreign trip
Do these in order, before the route is planned. 1. Datum check. Read the chart's title block or legend and write down the datum name. Compare it with the datum named by the tide service. If they differ, find the conversion or use a service that publishes in the chart's datum. 2. Clock check. Confirm the table's time zone, whether daylight saving applies on the date, and that every device on board agrees. Then run the depth check on the shallowest point of the route, add a margin for swell, squat and the difference between predicted and actual level, and write the result down. The table gives a prediction; the water gives the truth.
Calibrating a familiar mark
A mark you fish every week does not need the full foreign-chart procedure each time. Once you have fixed reference points — a painted step, a mooring scar, a rock that just awakens at a known stage — you can calibrate the table against what you see and work from the difference. That is quicker and usually more accurate for that one mark. Calibration does not replace the arithmetic for a new mark, a new country or a boat with a draft. It replaces it only where the reference points and the table have already been checked against each other, and where the weather has not pushed the level far from prediction. Keep the datum and the clock as the baseline and treat the local calibration as a correction on top. The habit that prevents most errors is to write the datum and the time zone at the top of the passage plan, next to the departure time. A plan that states "depart 06:40 local, heights above chart datum, LLWLT" is one that someone else can check. A plan with three bare numbers is one that only its author can misread.
Mistakes with datums and clocks
Adding a tide height to a charted depth without confirming both use the same datum. Assuming chart datum is mean sea level. Treating UK Lowest Astronomical Tide and Canadian LLWLT as the same plane. Reading a daylight-saving table as standard time, or the reverse. Using a tide prediction for a different station or a different day. Forgetting that the prediction excludes weather and planning with zero margin.
Sources
- EasyTide FAQs — UK Hydrographic Office · T1
- Vertical datum chart references — Fisheries and Oceans Canada / Canadian Hydrographic Service · T1
- About Tide Predictions — Australian Bureau of Meteorology · T1