Key facts
| Question | Answer |
|---|---|
| Medium | A density boundary inside the water column, usually the thermocline |
| Restoring force | Gravity acting on a displaced density interface |
| Frequency | Between the buoyancy frequency and the local Coriolis frequency |
| Period | Minutes to hours, far longer than surface waves |
| Amplitude | Many metres in coastal cases, hundreds in strong open-ocean cases |
| Surface sign | Convergence and divergence bands, often as slick lines |
| Steepening | Internal tides can collapse into packets of solitary waves |
| Depth | Energy concentrated where density changes fastest |
A wave that lives on a density boundary
That is an internal wave: a disturbance travelling along a density boundary inside the sea, invisible from above, readable on a sounder, and capable of relocating the fishing layer faster than most anglers adjust. An internal wave travels along the interface between two water masses of different density. The interface rises and falls, and the water on either side moves with it, often in opposite directions. The wave can be hundreds of metres to kilometres long and can displace the boundary by many metres while the sea surface stays almost flat. The restoring force is gravity. A parcel of water pushed above its equilibrium density level is heavier than its surroundings and sinks back; pushed below, it is lighter and rises. That oscillation is supported whenever the column is stratified, and its natural frequency — the buoyancy frequency — sets the upper limit for how fast the wave can oscillate. The lower limit comes from the earth's rotation. Internal waves exist in a frequency band between the buoyancy frequency and the Coriolis frequency, which is why their periods run from minutes to hours rather than the seconds of wind chop. In coastal water the band is wide and the waves are common; in the open ocean the periods stretch longer and the wavelengths reach kilometres. The reason the surface barely moves is a matter of density contrast. The difference between surface water and deep water is a few parts per thousand, while the difference between water and air is a factor of about eight hundred. A wave on the density interface therefore needs only a small surface expression to move a large volume of water below it. A boundary that rises two metres may lift the sea surface by a few centimetres, which is invisible against chop and completely hidden on a calm day. The energy is real; the surface signature is merely small.
What the surface shows
The surface is not entirely silent about the wave. Where internal motion converges the surface layer, foam, weed and slicks collect in bands; where it diverges, the surface is smoother and clearer. The result is a series of lines that can look like wind streaks but behave differently. The bands usually run parallel to the direction the internal wave is travelling, which over a shelf is commonly tied to the tide. If the lines appear at the same stage of the tide on successive days, an internal tide is the likely cause. If they move with the wind and re-form after every gust, they are Langmuir streaks or wind slicks instead. In calm, sunny weather the slick imprint can be the only visible evidence that anything is happening below. That is the condition in which internal waves matter most to fishing, because a glassy surface invites the assumption that the water column is still.
The layer moves, the fish do not have to
The practical effect is that the layer holding bait and fish is not fixed. It can rise or fall by 10 m or more over a tidal cycle, and it can move faster than an angler can reasonably re-rig. That changes what "fishing the thermocline" means. The thermocline is not a depth; it is a moving surface. An angler who found fish at twelve metres in the morning and returns to twelve metres in the afternoon may be fishing below the layer or above it, depending on which phase of the internal wave is passing. The fix is to read the sounder continuously rather than to trust a number. Look for the dense mark, the false bottom or the scattering layer, and set the lure relative to it. If the mark has moved five metres since the last drop, move the lure five metres. The fish are not necessarily following the layer voluntarily; they are inside it, and it carries them.
Internal tides follow the tide, not the tide table
Many coastal internal waves are generated where the tide flows over a shelf break, a canyon head or a sill. The tide pushes dense water up the slope and lighter water down, and the disturbance propagates shoreward as an internal tide. The strength of that generation depends on the tidal range and on the stratification. Spring tides produce stronger internal tides than neap tides, and a well-stratified summer column produces stronger ones than a weakly stratified winter column. That gives the layer movement both a fortnightly and a seasonal rhythm. The timing is not the same as the surface tide. The internal wave arrives after the forcing, sometimes by hours, and the delay depends on the distance to the generation site and on the speed of the internal wave. A tide table tells you when high water is at the surface; it does not tell you when the internal wave will reach your mark.
Solitons arrive as packets
In shallow water and strong stratification, an internal tide can steepen until the front becomes sharp and the disturbance breaks into a series of pulses. These are solitary waves, or solitons, and they behave like a train of separate surges rather than a smooth oscillation. For an angler, a soliton packet can appear as a sudden set of surface ripples in otherwise glassy water, sometimes with a visible surface current, followed by a return to calm. The pulses can be spaced minutes apart, and each one lifts and drops the layer in steps. Those steps are worth watching. A bait at a fixed depth can be lifted through the fish on one pulse and dropped below them on the next. The bite can switch on and off with the packet rather than with the hour, which is why a mark that produced steadily for ten minutes can go dead for ten more without anything else changing. Packet spacing is the clue to what you are dealing with. Solitons in a train arrive at fairly regular intervals, often several minutes apart, and each pulse has a similar shape. A single isolated rise with no follow-up is more likely to be a boat wake, a passing front or a tide phase change. Counting the interval between pulses, and confirming that the pattern repeats, separates a real packet from a one-off disturbance.
Fishing a moving target
The reliable approach is to keep the bait at the layer rather than at a depth. A downrigger, a weighted fly line or a slowly jigged lure can all be adjusted as the mark moves. A fixed sinker and a long soak are less adaptable, but they still work when the layer is stable for the session. Watch which of the two is moving. A mark that rises while the bottom stays fixed is the layer moving. A mark that splits and spreads is usually fish dispersing, which is a different event with a different response: the first calls for a depth change, the second for a change of position or presentation. In shallow water the internal wave can also stir the bottom and push cold, nutrient-rich water up a slope. That can switch a dead mark on where the wave meets a ridge or a reef, and it can switch a good mark off when the layer is pushed below the range of the bait.
A calm surface is not still water
Internal waves carry little surface signature, so a glassy sea can still have water moving at depth. In a confined channel or over a shallow sill, the internal motion can produce strong near-bottom flow and sudden changes in drift. That matters for anchoring and for anything suspended below the boat. A surface current meter may read almost nothing while the line at depth is being pushed sideways. If the boat is rigged deep, the load on the anchor and the angle of the line reflect the deeper flow, not the surface. It also matters for how the sounder is read. Most units draw a hard bottom and a soft layer using colour and return strength, and an internal wave can produce a false bottom that looks convincing. The tell is movement: a real bottom stays fixed on successive passes, while a false bottom drifts up and down. Mark the depth of the true seabed first, then treat any second strong return that moves independently as a density feature rather than as structure. Getting that wrong sends a lure to the wrong depth and makes a productive mark look empty.
Misreads on a moving layer
Treating the thermocline as a fixed depth. Fishing a remembered number instead of reading the sounder. Confusing internal-wave slick lines with wind streaks. Assuming the internal wave arrives with surface high water. Leaving a deep bait at a fixed depth through a soliton packet. Ignoring the spring–neap and seasonal control on internal tide strength. Reading a calm surface as proof that there is no current at depth.
Timing the arrival from the generation site
Internal waves travel slowly by surface standards. Speed is set by the density contrast and the layer thickness, and for a two-layer coastal case it sits close to the square root of the reduced gravity times the upper-layer depth. A density difference of about two kilograms per cubic metre across a 20 m upper layer gives roughly 0.6 m/s, or two kilometres an hour. A wave generated at a shelf break 6 km offshore therefore reaches an inshore mark about three hours later. That arithmetic explains the mismatch with the tide table. Forcing peaks at maximum tidal flow over the break, but the disturbance needs hours to cross the shelf. If the local tide turns at ten in the morning and the generation site is 6 km out, the layer disturbance arrives in the early afternoon, not at the turn. Carrying the number makes the arrival predictable within about an hour. Once a lift has been seen at a mark, note the time and the tidal stage. On the next spring tide with similar stratification the same lift should appear at a similar lag. Two or three observations turn the pattern into a schedule, and a schedule allows a drift to be planned around the layer rather than discovered through it.
Related reading
The thermocline layer Tide and fish position The freshwater lens and halocline Environment section index
Sources
- Internal waves — University of Hawaii, OCN620 course notes · T2
- Internal waves: a feature — L. R. M. Maas, Utrecht University · T2
- Internal waves and internal tides — NOAA Ocean Service · T1