Key facts
| Question | Answer |
|---|---|
| Height table | Time and height of the vertical turn |
| Current table | Peak flood, peak ebb and the reversal |
| Table split | One answers depth, the other answers control |
| Typical lag | 20 to 40 minutes between height turn and slack |
| Usable window | 20 to 40 minutes, shorter in wind |
| Spring effect | Stronger peak current and a sharper reversal |
| Best entry | Before slack, with the bar checked separately |
| Night plan | Rising tide, so delay leaves more water |
Give each table one question
An angler who plans it from the current table alone knows when the water will be manageable but not whether the bar has enough water over it. The working method is to assign each table its own question, then combine the answers into a single departure time with a margin on both sides. The height table answers whether the water is deep enough. Read it for the bar, the ramp, the sill and the route over a shallow flat. It tells you when a mark is reachable and when a boat can float across a shoal, and those are depth questions that a current prediction cannot answer. The current table answers whether the boat can be controlled. Read it for the moment of reversal, the peak speed on the flood and ebb, and the direction of the stream at the entrance. It tells you when a drift will track straight, when a jig will hold bottom and when an entrance is safe to cross. Neither table is a substitute for the other. A plan that uses only one is answering half the problem, and the failure usually appears at the worst moment: a boat arriving at predicted high water with the ebb already running hard, or a boat waiting for slack while the bar drains beneath it.
Why the two events separate at an inlet
The separation has a physical cause. An inlet entrance is a restriction, and the water behind it is a storage volume. When the ocean tide turns, the bay behind the throat has not finished filling or emptying, so the stream keeps running until the two levels equalise. The lag is therefore a function of geometry rather than of the moon. A short, deep entrance with little storage behind it turns almost with the ocean. A shallow lagoon behind a single narrow channel turns much later, because the channel cannot pass the volume fast enough. The same tide produces a small lag at one inlet and a large one at the next. A worked example shows the size of the effect. A bay of two square kilometres with a two-metre range has to exchange four million cubic metres in each half cycle, which is about six hours and twelve minutes. That averages 180 cubic metres per second. A throat 200 m wide and 5 m deep passes it at a mean speed near 0.18 m/s, with a peak near 0.28 m/s. Move the same bay behind a throat half that width and both speeds double, and the lag grows with them. That is why the lag is not a constant that can be transferred between marks. It must be measured at the inlet in question, or taken from a published current station, and it changes with the range of the tide because a spring pushes more volume through the same throat.
Finding slack when no current station exists
Where a current prediction is published for the passage, use it. Where none exists, two methods work. The first is a gauge pair: one tide station inside the entrance and one outside. The difference between the two curves drives the flow, so the moment the curves cross is a usable estimate of slack, and the maximum separation is a usable estimate of peak current. The second is direct observation. Anchor or drift near the entrance with a float and a watch, and record when the float stops moving relative to the predicted height turn. Repeat on a different range. Two observations establish whether the offset is stable; four across a spring-neap cycle establish its range. A chart can supply a first guess. A wide bay with a narrow throat will lag more than a narrow bay with a wide throat. An entrance with a shallow bar will lag more than a deep one, because the bar limits the flow at exactly the stage when the bay most needs to exchange water. The estimate improves quickly with one more measurement: the rate of rise at the inner gauge. If the inner water is still climbing steeply when the outer gauge has peaked, the stream is still filling the bay and slack is some way off. If the inner curve has flattened, the bay is close to equalised. Reading the slope of the inner curve is faster than waiting for a float to stop, and it works from the shore.
The window a boat can actually use
Predicted slack is a point; the usable window is a period. It opens when the flow has fallen enough that the boat holds position and closes when the new current has built enough to sweep it off the mark. In many inlets that period is twenty to forty minutes, and it is shorter than the interval of near-zero flow because wind and swell interfere. Wind is the usual spoiler. A fifteen-knot crosswind pushes a hull sideways whether or not the stream has stopped. When the breeze opposes the last of the ebb, chop builds early and the boat loses the settled feel that marks a true pause. The table can report zero and the water can still be unusable. Boat handling sets the other limit. A kayak holds position in less current than a deep-draft cabin boat, and a boat with a trolling motor can work a mark that a drift-only boat must abandon. The window is therefore a property of the boat as much as of the tide. Judge the window from things that do not move. A moored hull lies to the stream, and the angle of its bow against the mooring tells you the speed before the surface shows it; pot buoys lean and throw a small wake at the same threshold. When the boat begins to swing on its anchor without the rode tightening, the flow has dropped below the speed that matters for that hull. A boat that has stopped swinging while the surface still shows streaks of foam is inside a window that will close within minutes.
Timing the entry against the bar
The entry combines both tables. The height table says whether there is water over the bar at the time of arrival. The current table says whether the boat can be steered through the entrance at that time. The departure time has to satisfy both. Work backward from the bar. Find the earliest time the depth is sufficient, then check the current at that time. If the stream is still running hard on the ebb, either wait for the predicted slack or accept a faster crossing with more control input. If the depth only becomes sufficient after slack, the entry is a rising-tide entry and the current will be building against the boat.
Night, traffic and the exit
Getting out is half the plan, and it is the half that gets skipped. A window that opens at 09:00 and closes at 09:40 is not a window if the run back takes thirty minutes against the new current. Calculate the return at the speed the boat will actually make, not the speed on flat water. Night adds two constraints at once. The observed cues are weaker, and the traffic is often worse. Reflectors, lit pot lines and the boat's own drift are what remain, and the course-over-ground trace on the plotter is a better guide than the seat of the pants. Plan a night entry on a rising tide where possible, so a delay leaves more water rather than less. A slack window at a popular inlet is also the moment when other boats cross, and the channel can be crowded precisely when control is poorest. Arriving ten minutes early often buys an empty approach; arriving at the predicted minute puts the boat in a queue. The exit should carry the same margin as the entry: leave before the current builds, not at the moment it becomes uncomfortable, and keep a hard turn-back time that is independent of the fishing.
When zero never arrives
In a hydraulic inlet, river flow and tidal flow oppose each other. The surface may reverse while the deeper water continues seaward, or the current may fall to a minimum without stopping. The published tide can be correct for height and irrelevant to the stream. The same applies to dredged entrances, industrial channels and river mouths with regulated flow. In these places, slack is a minimum rather than a stop. A boat that expects zero current will be surprised, and a bait rigged for slack will not hold. River flow shows itself in the surface texture before a current meter confirms it. A plume of fresh water rides over the salt and produces a smooth, dark band with a sharp edge, and the band keeps moving seaward while the tide floods. Set a weighted lure down and watch the line: if the lure lands upstream of the boat and the line still stands at an angle, the deep water is running out under a surface that reads slack. Fish the layer that carries the bait, and weight for the deeper flow. The adjustment is to fish the weakest part of the flow rather than waiting for a stop. Use heavier terminal tackle than the height table alone would suggest, and treat the minimum as the centre of a short window. If the flow never falls below the speed at which the boat can hold, the mark is not fishable on that tide.
What to log
Record the predicted height turn, the predicted slack, the observed slack and the observed peak speed for one inlet. Keep the entries for a full spring-neap cycle. The log answers the questions the tables cannot. It shows the typical lag on a spring and on a neap, whether the lag changes with wind direction, and how wide the practical window really is for the boat. After one cycle, the next trip can be planned from local numbers rather than from a generic rule. Keep the log in the same place as the trip notes, with the tide range beside each entry. A lag that appears only on the big springs is a storage effect. A lag that appears only with a strong northwester is wind set-up, not a current offset, and it should not be folded into the tide calculation. Until the log exists, the safe method is the bracket. Arrive before the predicted slack, leave after the new current has begun, and keep a margin that matches the consequence of being wrong.
Sources
- Understanding Tides — NOAA Center for Operational Oceanographic Products and Services · T1
- Tides and Currents FAQ — NOAA Tides and Currents · T1
- Currents — Coastal Wiki · T2
- Tidal Currents — NOAA National Ocean Service · T1