Key facts
| Stage | What happens |
|---|---|
| Deep water | The crest travels in the reported direction |
| First contact with the bottom | The shallow part of the crest slows |
| Over a sloping bottom | The crest bends toward the slower side |
| Speed ratio | About 1.6 when depth falls from 50 m to 20 m |
| Shoaling | Height rises up to 1.5 times before breaking |
| At the beach | The approach angle is a local result |
| Long swell | A 15 s train feels the bottom near 175 m |
A crest is a line of separate wave speeds
Between the two lies a process that can turn a 30° offshore angle into an 18° beach angle, focus energy on a point, or leave a bay almost flat. Read the chart before you read the surf. A wave crest is not a rigid bar. It is a line of water particles, and each part of the line travels at a speed set by the depth beneath it. In deep water, the speed depends only on the wave period. In shallow water, the speed depends on depth: it falls as the square root of the depth. That difference is the engine of refraction. Imagine a crest approaching a coast at an angle. One end of the crest reaches the 20 m contour before the other end, which is still over 50 m. The shallow end slows to the speed appropriate for 20 m; the deep end keeps the speed appropriate for 50 m. The crest pivots around the slow end. The part that was ahead falls behind, and the crest rotates toward the shallower water. The process continues contour by contour, and the wave arrives at the beach with a smaller angle to the shoreline than it had offshore. The same mechanism explains why a long swell bends more than a short wind sea. A 15-second wave is about 350 m long in deep water, so the seabed starts to affect it at roughly 175 m of depth. It therefore has a long distance over which to refract. A 6-second wind sea is about 56 m long and starts to feel bottom near 28 m, leaving only a short distance to bend before it breaks. The bending is gradual because the speed changes gradually. A wave crossing a smooth, parallel seabed bends slowly and arrives with a consistent angle along the beach. A wave crossing a ridge, a channel or a buried reef bends abruptly, and the crest can develop a kink. Those kinks are visible in the surf as a change in breaker height or a section that peels faster than its neighbours.
What Snell's law tells you on a chart
The angle change follows Snell's law, the same relationship that governs light passing through glass. The ratio of the sines of the angles equals the ratio of the wave speeds: sin θ1 / C1 = sin θ2 / C2. In shallow water the speed is proportional to the square root of depth, so the speed ratio is the square root of the depth ratio. Take a swell arriving 30° off the depth contour in 50 m of water, then crossing the 20 m contour. The speed ratio is the square root of 50/20, or about 1.6. The sine of the new angle is 0.5 divided by 1.6, or 0.31, and the angle falls to about 18°. That is a bend of 12° from two chart numbers. The arithmetic is approximate, because it assumes straight, parallel contours and a shore-normal bottom, but it gives the direction and the order of magnitude. The calculation is most useful when the chart shows a clear change in contour direction. A coast with contours that run parallel to the shore produces little bending. A coast with contours that converge at a point or diverge inside a bay produces strong bending. The chart is the input; the surf is the output. The calculation also tells you when the wave will break. Instability sets in once the wave height reaches about eight-tenths of the local depth. Refraction changes the height as well as the angle, because the same energy is packed into a shorter crest, and shoaling can raise the breaker height to about 1.5 times the deep-water value before it breaks. A wave that converges on a point can break much farther offshore than the same wave on a straight beach. That is why a point can be surfable on a day when the adjacent beach is flat.
Points focus, bays straighten
A point is a natural lens. The depth contours wrap around it, and the crest segments on either side converge as they approach the tip. The convergence concentrates wave energy, raises the breaker height and pushes the break line farther offshore. The result is a peak that breaks early and a shoulder that peels along the point. Surfers read this pattern; anglers can use it to find structure. A bay is the opposite. The contours open outward, and the crest segments diverge as they enter. The wave energy spreads over a longer crest, the breaker height falls and the break line moves closer to the beach. The wave inside a bay is often smaller and more parallel to the shore than the wave at the headlands on either side. That is why a bay can be fishable when the open coast is too rough, and why the same bay can be disappointingly flat when the swell is small. The contrast is strongest when the coastline is concave or convex over a distance comparable to the wavelength. A small cove with a width of 100 m has little effect on a 300 m swell; the wave bends across the whole cove and arrives almost uniformly. A large bay with a width of several kilometres can straighten a swell that would otherwise hit the headlands at a steep angle. A point also creates a shadow. The wave energy that converges on the tip has to come from somewhere, and the lee side of the point receives less. That shadow is not absolute: diffraction bends some energy around the point, and the shadow is never completely calm. But the gradient from the tip to the lee is real, and it is one reason why the fishing changes over a short distance around a headland.
Why the buoy angle is not the beach angle
Most buoys sit well offshore, in water a hundred metres deep or more. The shoreline is another regime entirely. Over that gap the wave slows, steepens and swings toward the contours. The reported angle describes the open sea; the angle at the sand describes the seabed. Depth is the first thing to check. A sensor in 200 m of water is measuring a wave that the bottom has not yet touched. A sensor in 50 m may already be deep inside the refraction zone for a long swell. A sensor in 30 m is reporting a wave that has already begun to turn. The depth of the mooring is as important as the direction it reports. The second correction is the coastline. A straight coast with parallel contours bends the wave but keeps the angle consistent along the beach. A curved coast bends the wave differently at every point. The same offshore swell can arrive at 10° on one beach and 40° on another beach 5 km away, because the contours are different. The third correction is the period. A long swell bends more than a short sea, so the same buoy direction produces a different beach angle for each wave train. A forecast that gives a single direction for a mixed sea is giving an average, and the average may not describe the train that is actually breaking. The practical rule is to treat the buoy direction as a starting point and the chart as the translator. If the chart shows contours that run obliquely to the beach, expect the wave to bend toward shore-normal. If the chart shows a point or a bay, expect the angle to change along the coast. If the chart shows a straight, steep shoreface, expect little bending and a beach angle close to the buoy angle.
Using the chart before the cast
Start with a chart that shows depth contours at a useful interval, ideally 5 m or 10 m in the nearshore. Identify the contour that runs closest to your mark and note its direction. Then compare that direction with the buoy direction. A large difference means strong refraction somewhere between the buoy and the beach. Next, identify the shape of the contours around the mark. Contours that converge toward a point indicate a focus. Contours that diverge inside a bay indicate a spread. Contours that run parallel to the shore indicate a uniform arrival. The shape tells you whether the wave will be bigger or smaller than the regional forecast, and whether the angle will be consistent along the beach. Then walk the beach. A short walk along the waterline shows where the surf changes height and where the break line moves offshore. Those changes are the surface expression of the bottom. A section where the break is consistent and the foam lines are parallel is a section with uniform contours. A section where the break jumps or the foam lines converge is a section with a ridge or a channel. Finally, use fixed landmarks to judge the arrival angle. A rock, a groyne or a pier gives a repeatable reference. Note the angle between the crest and the shoreline at that reference. After a few sessions, you can compare the angle with the buoy direction and learn the local correction. That correction is more useful than a generic rule, because it is measured at the mark you fish.
When refraction does not explain the surf
Refraction is not the only process that changes a wave. Diffraction bends energy around an obstacle without a change in depth. Reflection sends energy back offshore from a sea wall or a cliff. Shoaling changes the height without necessarily changing the angle. Breaking dissipates energy and can reform the wave inside the surf zone. A cliff coast with deep water at the edge produces little refraction, because the wave has almost no distance over which to bend. The buoy direction is closer to the beach direction, and the surf is often steeper and more energetic. A shallow, flat surf zone can cause the wave to break far out and reform, which complicates any simple angle rule. A strong tidal current can refract the wave as well, because the current changes the effective depth and the wave speed. The most common misread is to attribute every change in surf height to refraction. A wave that is bigger at one end of the beach may be bigger because the bottom is shallower, because the wave is focusing, or because a local wind sea is adding height. The chart resolves the first two; the wind and the buoy period resolve the third.
A worked example
A buoy in 80 m reports a 2.0 m swell at 14 seconds from 240°. The chart shows a bay with contours that run northwest to southeast at the entrance and curve to run east-west inside the bay. The buoy direction is 240°, which is 30° off the entrance contours. The wave crosses from 50 m to 20 m at the entrance, so the speed ratio is about 1.6 and the angle falls to about 18°. Inside the bay, the contours curve further, and the wave bends again toward shore-normal. At the inner beach, the angle may be 10° or less. The height changes too. The convergence at the entrance raises the wave, and the divergence inside the bay lowers it. A 2.0 m offshore swell can be 2.5 m at the entrance and 1.4 m at the inner beach. That difference is why the entrance is dangerous on a day when the inner beach is calm, and why the fishing is different at the two marks. The final check is visual. Stand at the inner beach and look at the break line. If the break is parallel to the shore and the foam lines are straight, the wave has been straightened by the bay. If the break is higher at one end and the foam lines converge, the wave is still feeling the entrance. The chart predicted the pattern; the surf confirms it.
Sources
- Longshore Currents (Currents Tutorial) — NOAA National Ocean Service · T1
- Waves (JetStream) — NOAA · T1
- JetStream Max: Anatomy of a Wave — NOAA · T1
- OCNG 251: Oceanography (Waves), Spring 2012 lecture notes — Texas A&M University at Galveston · T2