Tidal Bores: The Wave That Runs Against the River

In most rivers the flood arrives quietly. The downstream current slows, stops, and reverses. In a few rivers the reversal arrives as a visible wave that moves upstream faster than a person can walk, and the water behind it keeps rising for more than an hour. That wave is a tidal bore: the leading edge of the flood, steepened by the shape of the estuary until it becomes a front you can see and hear.

tides
Cover illustration: Tidal Bores: The Wave That Runs Against the River

Key facts

QuestionAnswer
What it isSteep-fronted tidal wave running up a shallow estuary or river
RequirementsLarge range, funnel-shaped entrance, shallow sloping bed
Rivers with boresAbout 100 worldwide, roughly a fifth in the UK
Severn heightUp to about 2 m
Severn frequencyRoughly 250 times a year
Best Severn tidesSpring tide above 14 m at Avonmouth
QiantangOver 4 m high, 3 km wide, faster than 24 km/h
Rise behind the frontAbout 1.5 hours of rising water
Timing sensitivityRain and wind can shift arrival by about 15 minutes

The front is the flood, not a separate tide

The front is a spectacle and a hazard in equal measure, and the water behind it is the part that matters for navigation and for fishing. A bore is not a second tide that arrives after the first. It is the same flood, arriving in a shape that a shallow, narrowing channel imposes on it. Every tide is a long wave. In a bore, the leading edge of that wave has steepened until the rise in level happens over metres rather than kilometres. The distinction matters for prediction. A bore is governed by the same astronomical tide as the rest of the coast, so it appears on the spring tides and fades on the neaps. There is no separate bore timetable. The tide table for the nearest standard port is the starting point, and the river geometry converts that prediction into a wave. The local names are a guide to how long people have watched the effect. NOAA lists eagre for the English bore, mascaret for the French, and pororoca for the Brazilian. The names differ because the event is visible and coastal communities built calendars around it, not because the physics differs between rivers.

Three conditions have to line up

A river produces a bore only when three conditions coincide. The range must be large. The flood has to drive a volume of water into the estuary that is big enough to steepen as it enters. A coast with a two-metre spring range rarely produces a bore, however favourable the channel; a coast with a ten-metre range has the raw material. The entrance must narrow and shallow rapidly. A funnel concentrates the incoming water, and a shallow bed slows the wave front relative to the crest behind it. That difference in speed is what allows the front to sharpen. A wide, deep entrance spreads the flood and lets it arrive gradually. The bed must slope gently enough for the front to travel a long way without dissipating. A steep, rough river burns the wave out within a kilometre or two. A long, smooth, gently sloping channel lets the bore run for tens of kilometres and gives the observer time to see it. Most rivers fail at least one test. Their range is too small, their entrance too wide, or their bed too steep. In those rivers the flood still arrives, but it arrives as a gradual acceleration rather than a wave.

Why the front sharpens

The steepening is a nonlinear effect. The water at the crest of the advancing flood is in deeper water than the water at the front, so it travels faster. The crest catches up with the front, and the leading edge steepens. In deep water this process is slow and the wave stays smooth. In shallow water the speed of the wave depends strongly on depth, so the difference between the crest and the front is large. The front steepens quickly, and once it is steep enough it breaks and becomes turbulent. That is the same mechanism that turns a smooth swell into a breaking wave on a beach, applied to a tide in a channel. The bore is a beach break that travels upstream. Whether the front breaks depends on how fast the flood runs relative to the wave it creates. Wave speed in shallow water is set by depth, so a front travelling at about the wave speed stands as a smooth undular rise, and a front travelling faster steepens until it breaks. That ratio explains the progression on one river: a ripple at neap, a breaking crest at spring, and the loudest bores on the tides that drive the front hardest against the channel. The turbulence at the front is what makes the bore audible. The breaking crest entrains air, and the roar carries a long way over water. On the Qiantang the sound can be heard more than an hour before the front arrives. An undular bore arrives as a train of smooth swells instead of a single breaking crest. It is quieter, it throws no spray, and the level rises in steps over a few minutes. The current still reverses behind it, and the reversal still lifts sediment and moves debris, so the settled-water window opens in the same way. Judging a bore by its noise alone misses the undular tides, which are the common form on the smaller rivers.

Where bores occur

About 100 rivers worldwide are known to produce bores, and roughly a fifth of them are in the United Kingdom. The concentration follows the tidal range: the British Isles sit in a part of the North Atlantic where spring ranges are large, and several of their estuaries are funnel-shaped with shallow beds. The Severn, Dee and Mersey are the best-known British examples. The Severn in particular has a long, narrowing funnel and a bed that slopes gently for tens of kilometres, which is why its bore is the most watched in the world. The Qiantang in south-east China is the largest. It runs over 4 m high, spreads about 3 km wide at some points, and travels faster than 24 km per hour. Reflected waves off the banks can reach 10 m, and the roar is audible more than an hour before the front. The list is not fixed. A river can gain or lose a visible bore as its channel shifts, and a bore that is dramatic on a spring tide can vanish on a neap. Published inventories tell you where to look, not what you will see on a given day.

Timing the Severn

The Severn Bore runs approximately 250 times a year, from a small ripple to a wave up to about 2 m. The best bores come with very high spring tides, above 14 m at Avonmouth. The bore is a travelling front, so its arrival time is listed relative to high water at the reference port. The standard offsets are approximately 15 minutes before high water at Newnham, 25 minutes after at Epney, 45 minutes after at Minsterworth, 1 hour after at Stonebench, 1 hour 20 minutes after at Over Bridge, and 1 hour 25 minutes after at Maisemore. These are averages, not appointments. Rain in the catchment is the main reason the averages fail. Fresh water running down the river opposes the flood, and a river in spate can reduce a predicted bore to a ripple or suppress it entirely. A dry spell before a big spring tide is the condition to look for. Wind matters too. A strong onshore wind can push the front along and shift its arrival by about 15 minutes; an offshore wind can flatten the crest. The same predicted height can produce a good bore and a poor one on consecutive tides. Behind the front the water keeps rising for about 1.5 hours. The river changes from a calm, slowly ebbing stream into a turbulent upstream flow within minutes of the front passing, and the level continues to climb long after the visible wave has gone.

The Qiantang and the hazard

The Qiantang is the scale example and the safety lesson in one. A bore of that size is not something to stand in front of. Reflected waves can rise suddenly and break over the banks, and spectators have been washed away by waves arriving after the front had passed. The hazard continues behind the front. The water there is deep, fast and full of debris torn from the banks, including whole trees. A person or a small boat caught between the front and the bank has very little time to react. The same pattern applies at smaller scale on any bore river. The front arrives fast, the depth jumps, and the current reverses within minutes. A sandbank that is dry before the bore can be under a metre of moving water shortly after it passes.

Fishing a bore river

Do not fish the front. The bore itself is a mixing event: it lifts sediment, moves debris and redistributes bait, but the water at the front is the least controlled water in the river. The useful window opens after the initial surge has settled, when the river is deep and the current is organised. Bait that has been scoured out of the banks and flats is carried downstream, and fish hold in the eddies and slack water at the edges of the flow. That is where to fish, and it is a window of a couple of hours rather than a full tide. The ebb after a bore is often better than the flood. The river drains a large volume through the same channel, the current is strong and steady, and the water clears as the sediment settles. Fish that were dispersed by the front concentrate again on the falling water. Check both the tide height and the recent rainfall before planning a session. A predicted spring tide above the bore threshold is the first condition; a dry spell in the catchment is the second. If the river is in spate, the bore may be small or absent even on a big tide, and the fishing plan should shift to the sheltered edges.

Safety on a bore river

Watch from above the high-water line, and give yourself an exit route that avoids the channel. Reflected waves can arrive after the front has passed, so the danger does not end when the visible wave is gone. Do not anchor, wade or park a boat in the path of a known bore. The front arrives faster than a person can move on soft ground, and the depth change is abrupt. A boat anchored in the channel will be picked up, swung and filled. Keep clear of the banks where the bore reflects. The reflection is what produces the largest waves, and it happens on the outside of bends where the channel is deepest.

A bore is not a separate tide

Treating a bore as a separate tide rather than the front of the flood. Expecting a bore on every spring tide in every estuary. Using the bore time at one village for another 10 km upstream. Ignoring recent rain when judging whether a bore will appear. Standing on a sandbank that the bore will cover. Assuming the danger ends when the visible front passes. Fishing the front instead of the settled water behind it.

Sources

  1. Tides and Currents Glossary — NOAA Tides and Currents · T1
  2. Tidal river bores — National Tidal and Sea Level Facility · T2
  3. Tides and Currents FAQ — NOAA Tides and Currents · T1