Key facts
| Term | Driver | Typical size |
|---|---|---|
| Astronomical tide | Moon and sun | Metres; predicted in tables |
| Inverse barometer | Surface pressure | About 1 cm per hPa |
| Wind setup | Sustained onshore wind | Decimetres to a metre |
| Wave setup | Breaking waves | Roughly 15–20% of breaker height |
| Run-up | Swash on the beach | Slope and period dependent |
| Total | Sum of the terms | Usually above the predicted tide |
The four terms
Each term is small enough to ignore on a calm day and large enough to matter when they coincide. Reading a total water level means separating the four, estimating each from the forecast, and adding a margin that reflects how little confidence the smallest terms deserve. Astronomical tide is the predictable part. It is computed from harmonic constituents and published years ahead, and it is the only term that appears in a standard tide table. Storm surge is the meteorological part. It combines the inverse barometer effect, wind stress on the water surface and, in shallow water, the transport of water by waves. NOAA's definition separates the weather-driven rise from the astronomical prediction, which is the right way to keep the two terms in view: the table supplies one, the forecast supplies the other. Wave setup is the local rise in mean water level caused by breaking waves. As waves break, they release momentum, and the resulting stress raises the mean surface at the shore. It is a shoreline effect, not a deep-water one, and it disappears when the waves stop. Run-up is the vertical reach of the swash. It is not a change in mean level but the maximum height the water reaches on the beach or structure, and it depends on wave height, period and slope.
Pressure moves the surface
The inverse barometer effect is the simplest term to estimate. A low-pressure system allows the sea surface to rise, roughly one centimetre for every hectopascal below normal. A deep low with a central pressure 30 hPa below the surroundings lifts the water by about 30 cm. The relationship is close to linear over the range of pressures that occur in weather systems, and it applies to the open ocean as well as the coast. It is also the term that is easiest to overlook, because a pressure chart does not look like a water-level forecast. The effect is not instantaneous. The ocean takes hours to adjust, and in a fast-moving system the response lags the pressure change. For a slow-moving front the adjustment is close to complete; for a rapidly deepening low the water may arrive after the pressure minimum has passed. The difference across the map matters more than the centre value. The sea answers to the gradient, so a 990 hPa low ringed by 1015 hPa raises the water by roughly 25 cm, while the same 990 hPa sitting inside a broad field of 995 hPa raises it by 5. That is the gap between a low that lifts water over a slipway and one that passes without a mark on the coast. Read the isobars around the centre, then the centre itself.
Wind stacks water against the shore
Sustained wind pushes surface water downwind. Against a coast, the water has nowhere to go and piles up, producing a setup that grows with wind speed, fetch and duration, and shrinks with depth. The relationship is nonlinear. Setup scales roughly with the square of wind speed, so a 40-knot wind produces about four times the setup of a 20-knot wind over the same fetch. That is why a moderate blow barely registers while a gale moves the shoreline by half a metre. Fetch and duration set how much water is available to pile up. A long fetch with steady wind produces a larger setup than a short one, and a wind that blows for twelve hours moves more water than a squall that lasts twenty minutes. In an estuary, the shape of the basin can amplify the effect further, because the water is confined and cannot spread sideways. The same wind also drives the surface layer at an angle to the coast, and the resulting transport can raise or lower the level depending on the orientation of the shoreline. A coast with the wind parallel to it may see little setup, while a bay that faces the wind directly sees the full effect. That is why two adjacent beaches can flood differently on the same forecast. The angle sets the size of the effect. Only the onshore part of the flow piles water against a shore, the component pointing straight at the coastline. A wind arriving 45 degrees off the perpendicular brings roughly seventy per cent of its speed to bear, and a wind running parallel to the beach brings none of it. A 30-knot wind square to a bay head is therefore a larger water-level event than the same wind along a straight coast, though the forecast reads identically in both places.
Wave setup at the break
Wave setup is the rise in mean water level inside the surf zone. As waves shoal and break, they convert wave energy into a shoreward momentum flux, and the resulting gradient in radiation stress raises the mean surface. A working estimate is that setup at the shoreline is roughly fifteen to twenty per cent of the breaking wave height. A two-metre breaker therefore raises the mean level by about 30 to 40 cm, which is enough to turn a dry slipway into a wet one. The estimate is a planning figure, not a prediction for a specific beach. Setup depends on the wave period, the beach slope and the shape of the surf zone, and it varies along a coast with the bathymetry. The order of magnitude is what matters for deciding whether a route stays open.
Run-up reaches higher than the mean
Run-up is the swash excursion above the still-water line. It is driven by the bore that remains after breaking, and it can reach well above the setup level, especially on a steep beach with long-period waves. Run-up increases with wave height and period and decreases with beach slope in a way that is not intuitive: a steep beach reflects more energy and produces a higher swash for the same wave, while a flat beach dissipates the energy over a wider zone. A long-period swell on a steep shingle beach can run up several metres. The practical consequence is that the highest water on a structure is not the mean level plus setup. It is the mean level plus setup plus the run-up of the largest wave in the set. Access decisions should use the upper figure, not the average. Run-up arrives in groups. A swell travels as sets of three to eight larger waves with a lull between them, and the highest swash usually belongs to the last and largest wave of the group, because the earlier ones have already wetted the beach face and cut the friction under the following swash. Two minutes of watching gives a better figure than one wave. The dry line above the wrack records the group maximum, and that line is the one to check against the route.
Adding the terms
The four terms are not independent, and simple addition overstates the total in some situations and understates it in others. Wind setup and wave setup both derive from the same wind and wave field, so treating them as separate maxima is conservative. Pressure and wind surge often peak together in a storm, which is why the combined total can be larger than either term suggests. For planning, a conservative sum is the right approach: predicted tide, plus the forecast surge, plus an allowance for wave setup and run-up based on the sea state. The result is an upper bound that is deliberately pessimistic. A route that works at the upper bound will work in the conditions. The sum also explains why a small tide can produce a large water level. A 0.8 m tide with a 0.5 m surge, 0.3 m of setup and a metre of run-up is a 2.6 m water level at the structure, even though the table never shows more than 0.8 m.
Reading the forecast for total level
Surge forecasts are published by national agencies and are usually expressed as the difference from the predicted tide, not as an absolute level. Read the surge value, add it to the tide at the time of interest, and then consider the wave terms separately. Wave forecasts give significant height and period at a stated location, often offshore. The height at the beach is not the offshore height; shoaling and breaking change it. A two-metre offshore sea may produce a one-metre breaker on a shallow shore, or a two-and-a-half-metre breaker on a steep one. Local knowledge fills the gap. A harbour master or a commercial operator will know which wind direction produces flooding at the ramp and which forecast underestimates the sea at the entrance. That knowledge is usually expressed as a rule of thumb, and it is more reliable than a generic formula.
Decision rules
For shore access, compare the total water level with the height of the route, and add the run-up of the largest set. If the route is a slipway or a low bridge, the relevant figure is the upper bound, not the mean. For a boat at anchor, the total level sets the scope and the swing. A higher level means more water over the anchor and a different angle of pull, and a falling level after the surge passes can leave the boat aground on a falling tide. For a mark that depends on a stage, the total level changes when the stage arrives. A surge can make a low tide fish like a mid tide, or make a high tide overtop structure that normally stays dry. The stage name is a description of the astronomical tide, not of the water.
Common errors
The first error is to use the tide table as a water-level forecast. It is one term, and on an exposed coast in weather it can be the smallest term. The second is to use offshore wave height as the height at the shore. Shoaling, refraction and breaking all change it, and the change is not a constant factor. The third is to ignore duration. A wind that blows for an hour does not produce the same setup as the same wind for a day, and a fast-moving front may produce less surge than its pressure suggests. The fourth is to treat the terms as independent maxima. They often peak together, and the conservative sum is the right planning figure. The final check is observational: compare the actual water level at the gauge with the predicted tide and the forecast surge. The difference is the local allowance that no forecast supplies.
Sources
- Storm Surge Overview — NOAA National Hurricane Center · T1
- Wave Setup — Coastal Wiki · T2
- Wave Run-up — Coastal Wiki · T2
- Tides and Water Levels — NOAA National Ocean Service · T1
- Storm Surge — Bureau of Meteorology (Australia) · T1