Key facts
| Quantity | Tide prediction | Current prediction |
|---|---|---|
| Primary output | Time and height of high and low water | Time and speed of maximum flow |
| Secondary output | Shape of the curve between turns | Time of slack water |
| Unit | Metres or feet | Knots or metres per second |
| Main use | Access, depth, wading route | Drift, position, when the flow pauses |
| Open-ocean value | Small rise | Often weak or negligible |
| Inlet value | Amplified by confinement | Can be strong on a modest range |
| Update cycle | Astronomical, predictable years ahead | Astronomical, but more local |
Two products, two questions
The rise and fall of the surface drives the horizontal flow, so a bigger range generally means a stronger current. The link is real but not proportional, and the timing offset between the two can be six hours. Tide predictions give the times and heights of the tides. Tidal current predictions give the times and speed of maximum current and the times of slack water. They are separate products, generated by separate models, and neither is a reformatting of the other. The physical link is straightforward. The gravitational pull of the Moon and Sun raises and lowers the ocean surface, and that vertical movement drives horizontal motion in bays, harbours and estuaries. As the tide rises, water flows in as a flood current. As it falls, water flows out as an ebb current. The link explains the direction but not the speed or the timing. Those come from geometry: the size of the opening, the volume of the basin, the depth of the channel and the shape of the coast. Two inlets with the same range can have completely different currents.
Height and flow are not proportional
In the open ocean the actual rise of the tidal wave is small, one to a few feet. The visible range grows when the wave enters shallow water, meets a land mass or runs into a confining channel. The same confinement that amplifies height also squeezes the flow. A wide, deep entrance can pass a large volume of water with little visible speed. A narrow inlet with the same range has to move that volume through a smaller opening, so the current can be strong. That does not mean a small range always gives a weak current. A long, narrow channel can accelerate a modest range, and a hydraulic passage can run hard on a height difference between two basins rather than on the local range at all. Volume, not height, is what the current carries.
Where the fastest flow sits
Three geometries describe the timing, and each produces a different relationship between the height curve and the current curve. In a standing wave, the flow peaks between the tide turns and slack sits close to high or low water. Height and flow are offset by about a quarter of a tidal cycle. In a progressive wave, the flow peaks near the tide turns and slack sits between them. The surface and the current are roughly in phase, which is the pattern most people assume applies everywhere. A hydraulic current peaks when the difference in height between the two connected bodies is greatest, which can happen at any stage depending on how the two basins fill. Geography gives a hint. Progressive behaviour is common at the ocean entrance to a bay, while standing behaviour is common at the head of a larger bay. A mark near the mouth and a mark near the head can therefore have different timings on the same day, and the tide curve tells you which is which only after you know the geometry.
Reading a current table
A current table is written differently from a tide table. It lists the times of maximum flood and maximum ebb, the times of slack water, and the speed at the maximum. Some tables give the speed at several depths. The first check is coverage. A station labelled weak and variable has currents that do not exceed about a quarter of a knot and are driven mainly by wind and weather. For those locations no useful prediction is published, and the tide height remains the better product. The second check is depth. The surface line is the fastest; the near-bottom line is slower. Match the depth line to how deep the bait or lure runs, not to the top row of the table. A surface speed applied to a bottom bait overstates the drift. The third check is the direction convention. Current tables normally give a flood direction and an ebb direction in degrees, and the speed applies along that axis. A crosswind or a secondary channel can push the boat off the predicted axis even when the speed is right. A float measures what the table cannot. Drop a weighted float or a marked buoy at the start of the pass, time it over a measured distance, and convert to speed: a float that covers 30 metres in 60 seconds is moving at about 0.5 metres per second, which is roughly one knot. Repeat at the depth of the bait by using a weighted drogue. Two measurements, one at the surface and one near the bottom, show the shear that the table compresses into a single number.
Choosing the table for the mark
The choice follows from what the session depends on. Fishing a channel, pass or inlet: open the current prediction first. Read the times of maximum flood, maximum ebb and slack. The tide height tells you whether the water is high enough; it does not tell you how hard it is moving. Walking a bar, a ledge or a slipway: open the tide prediction first. Read the heights and the times of high and low water. The current matters only as a secondary hazard. Planning a drift: use the current direction and speed, then adjust for wind. The tide height does not tell you where the line will end up. Checking a shallow entrance: use both. The height decides whether the mouth is passable, and the predicted flow rate sets how long a crossing will take. Writing a plan: record the two predictions separately with the station name and the date, so a later comparison is honest about which product was used.
Five situations where height misleads
A weak-current coast. On an open shore with little tidal flow the current may be negligible even when the range is large. A height table is the only useful product, and adding a current correction invents a problem. A river-dominated estuary. Freshwater outflow can dominate the surface movement. The tide height may still be correct, but the current prediction may not describe the river push, and a flood tide can be cancelled by a spate. A wind-driven surface layer. A steady wind can move the top layer independently of the tide. A boat drifting with the wind is not drifting with the current, and the two can oppose each other. A hydraulic passage. The flow follows the difference between two basins, not the local high-water time. Use a current table or a pair of gauges. A mark with no current station. Do not convert height into speed. Observe the drift with a float or a marker and use a margin.
Building a drift plan from current data
A drift plan needs three numbers: the direction of the flow, the speed at the depth fished, and the time until the flow changes. Take the direction and speed from the current table for the hour of the pass, not for the day's maximum. A pass at mid-tide may run at half the peak speed, and a plan built on the peak will overshoot. Allow for the wind. Estimate the surface drift from a floating marker before the pass, compare it with the predicted current, and note the difference. That difference is the wind's contribution and it will persist for the session. Set a start and a finish. A drift without an end point is not repeatable, and a repeatable drift is how a mark is learned. Finally, record the actual track. After a few passes the log shows whether the prediction or the observation is the better guide for that mark, which is the only comparison that matters locally.
What the tables leave out
Both predictions describe the astronomical tide. Wind, weather and river flow are not included, so a windy day can run faster or slower than the number on the screen. Both are point predictions. A current station describes one location, and the flow a hundred metres away can differ in speed and direction because of a shoal, a pier or a channel bend. Neither predicts the waves. A strong wind against a tidal current produces steep, broken water that no current table shows, and that sea state is often the real limit on a session.
Mistakes that change the plan
Using the tide height as a proxy for current speed. Assuming slack water is at high tide on a progressive inlet. Comparing a current speed in knots with a tide height in metres. Using an ocean-entrance current for a mark at the head of the bay. Ignoring wind when the surface drift matters. Reading only one of the two predictions for a passage that needs both. Applying a surface speed to a bottom bait. Planning a drift on the day's maximum rather than the hour of the pass.
A short checklist
Before the session, decide which question matters: depth or flow. Open the matching prediction first, then the other as a cross-check. Note the station, the datum and the depth row. On the water, verify with a float or a marker. Prediction and observation together are stronger than either alone, and the difference between them is the local knowledge that no table contains.
Related reading: tide lag in bays and estuaries, estuary mouth geometry, tide stage by shore type.
Sources
- Frequently Asked Questions: relationship between tides and tidal currents — NOAA Tides & Currents · T1
- Our Restless Tides, Chapter 5: Factors Influencing the Local Heights and Times of Arrival of the Tides — NOAA Tides & Currents · T1
- What are tides? — NOAA National Ocean Service · T1
- Understanding NOAA Current Predictions (User Guide v5) — NOAA Tides & Currents · T1