Downrigger: The Counter Reads Cable Out, Not Lure Depth

A downrigger is a winch with a boom, and its counter measures cable paid out. That number is not the depth of the lure. The ball trails behind the boat, the cable leaves the pulley at an angle, and the lure rides above the ball. The gap between the counter and the actual fishing depth is the part that decides whether the spread is in the strike zone or above it.

matching
Cover illustration: Downrigger: The Counter Reads Cable Out, Not Lure Depth

Key facts

Key factDetail
Cannon Magnum 10 STX boom24 to 53 in, telescopic stainless steel
Cannon cable250 ft of 150 lb stainless steel
Cannon weight capacity20 lb
Cannon retrieval speed250 ft per minute, not adjustable
Scotty boat guidanceWide-beam hulls 16 ft and longer
Scotty ballast guidance7 to 12 lb for most conditions
Scotty cable angleNo more than 30 degrees at trolling speed
Scotty circuit breaker15 A; can trip lifting over 20 lb from depth
Release positionAt least 5 ft below the stopper bead
Depth correctionCounter depth multiplied by the cosine of the cable angle

The counter measures cable, not depth

Choosing a downrigger means choosing ballast, boom length, release tension and a mounting point that can carry the load. A depth counter is a turns counter on the spool. It knows how much cable has left the reel, and it assumes the cable is straight down. At rest, or at very low speed in calm water, that assumption is close enough. Under tow, it is not. The ball and cable form a pendulum that swings aft, the cable leaves the pulley at an angle measured from vertical, and the lure sits on a shorter vertical line than the counter suggests. The error is largest exactly where deep trolling matters. At a 30 degree angle, the vertical component is about 87 percent of the cable out. At 45 degrees it is about 71 percent. At 60 degrees it is half. A counter reading of 150 ft therefore describes a lure running near 130 ft, 106 ft or 75 ft depending on the angle, and the angle changes with speed, current and ballast. Treat the counter as a repeatable reference rather than a depth gauge. It tells the operator that the same setting produced the same cable length. Converting that length into depth requires one more number: the angle of the cable at the pulley.

Ballast sets the angle

The ball is not there to sink the lure. The lure is already weighted or diving. The ball exists to hold the cable down and to keep the release clip at a controlled depth, and its weight is the main variable that resists blowback. Cannon rates the Magnum 10 STX for a 20 lb weight. Scotty's manual states that 7 to 12 lb is adequate for most fishing conditions and that the cable should not drag back at more than a 30 degree angle at trolling speed. Those two statements describe the same trade. A heavier ball tracks straighter and fishes closer to the counter number, but it loads the boom, the cable, the clutch and the retrieval motor harder. The 20 lb figure is a ceiling, not a target. Island Fisherman Magazine gives a working relationship for salmon trolling: about 45 degrees with a 15 lb ball at normal speed, and roughly 30 degrees with an 18 lb ball. The numbers are a guide for one fishery rather than a universal table, but the direction is reliable. The angle examples in this section are based on 2018 trolling practice for Pacific salmon and remain a usable starting point for other fisheries. Adding three pounds of lead at trolling speed removes a noticeable amount of angle, and removing angle buys back depth accuracy. Ballast also changes the fight. A heavier ball swings less when the boat rolls, but it stores more energy if the cable parts or the terminator fails. The snap, the crimp and the cable end are the parts that see that energy first.

Blowback arithmetic

The correction is trigonometry, not a manufacturer's opinion. Measure the angle between the cable and vertical at the pulley, take the cosine, and multiply by the counter reading. At 45 degrees, a 150 ft counter reading gives 150 × 0.707, or about 106 ft of vertical depth. That is a 44 ft error, which is larger than most trolling strike zones. The same equation runs backward. To fish at 150 ft with the cable at 45 degrees, the counter has to read 150 ÷ 0.707, or about 212 ft. That is the number to dial if the sonar mark is at 150 ft and the cable is clearly angled. Two cautions belong with the arithmetic. First, the angle is rarely constant across the cable; the ball is deeper than the pulley and the cable curves under load, so a single angle measured at the top is an approximation. Second, the lure is not at the ball. It trails behind on its own leader, and a flasher or dodger adds drag that lifts it further. The cosine correction gets the ball close; the lure remains above and behind it. Use the calculation to choose a starting counter setting, then verify with the sonar. A downrigger that is consistently fishing high shows up as marks below the lure line, and the fix is either more ballast, a slower speed or a higher counter setting.

Cable, braid and the spool

Cannon supplies the Magnum 10 STX with 250 ft of 150 lb stainless steel cable. Scotty's manual is explicit that nylon or other monofilament must not be used on the downrigger spool: nylon stretches under load and shrinks back onto the spool with enough force to damage it, and the manual states that monofilament use voids the warranty. Braided downrigger line is accepted, and steel cable remains the standard where abrasion and cut resistance matter. Steel cable has three practical behaviours. It hums at trolling speed, which some operators use as a speed indicator. It kinks permanently if it is allowed to go slack, and a kink is a fatigue point. It also develops meat hooks, the small broken strands that cut gloves and fingers. A cable with a kink or a broken strand should be replaced rather than straightened. Braid runs quieter and does not develop the same wire spikes, but it is more vulnerable to abrasion at the ball end and it stretches less than nylon yet more than steel. The terminator, the crimp or knot that attaches the snap, is the weakest point in either system and deserves inspection before every trip.

Release tension

The release clip performs two opposite jobs. It must hold the fishing line against the drag of the lure, the flasher and the cable at trolling speed, and it must let go when a fish strikes or when the angler lifts the rod. A clip set too light false-releases and sends the bait to the surface. A clip set too heavy refuses to release, and the fish fights the ball instead of the rod. Scotty's Power Grip release is adjusted in two ways: the line is placed further into the jaws to increase grip, and a tension slider is moved outward to increase tension further. The manual also requires the release clip to sit at least 5 ft below the stopper bead, so that the bead can trip the auto-stop without the clip fouling the pulley. Set the release by testing it in the water, not on the dock. Deploy the lure to trolling speed, watch the rod tip, and confirm that the line stays in the clip through a turn. Then strike the line by hand, as a fish would, and confirm that it pops free cleanly. A clip that needs a hard snap to release is set too heavy for the rod in use.

Boom length and boat geometry

Boom length is a reach-and-clearance decision. Cannon's Magnum boom extends from 24 to 53 in. A longer boom puts the cable further outboard, away from the hull, the prop and the transom, which matters in a turn and when several downriggers are fishing different depths. A shorter boom is easier to reach and puts less bending load on the mounting base. Scotty states that the Depthpower 30 in and 60 in electric models are intended for wide-beam boats of 16 ft and longer, and that installation on smaller boats is not recommended. The reason is leverage: a long boom with a heavy ball applies a large moment to a small, lightly built hull, and the motion of a small boat in a chop adds to it. Boom angle also affects the release. A boom that is tilted up shortens the effective drop and changes the angle at the pulley, so the counter correction has to be recalculated after any boom adjustment.

Mounting and retrieval

A downrigger base sees tension, compression and vibration. It should be through-bolted or bedded to a surface with enough thickness to spread the load, and the mounting area should let the operator reach the ball, the release and the rod holder without leaning over the side. Scotty's manual warns against leaning out to reach the weight and against retrieving a loaded or snagged cable by hand. The retrieve sequence matters more than the deploy sequence. When a fish is hooked, the manual recommends bringing the downrigger weight up before landing the fish, so the fish cannot tangle in the cable and the ball cannot hit bottom if the boat drifts into shallower water. All downriggers should be wound up before the boat stops to drift. A pair of wire cutters belongs at the helm. If the ball snags, the tide or wind on the boat can load the cable far beyond its rating, and the safe release is to cut the wire from a position clear of the boom. The boom can fly up when the cable parts, so nobody should be leaning over it.

Current, speed and the angle as a speed gauge

The cable angle is also a speed readout. Island Fisherman notes that the angle grows as trolling speed rises, and that the same angle behaves differently with and against the tide. Trolling with the current reduces the lure's speed through water for a given boat speed; trolling against it increases both lure action and blowback. That makes the angle useful in two directions. If the angle is larger than normal at the usual throttle setting, either the speed is up, the current is against the boat, or the ball is too light. If the angle is smaller, the opposite is true. The counter setting should be adjusted after the angle is read, not before.

When a downrigger is the wrong tool

A downrigger earns its space in deep, open water where a bait has to be held at a precise depth while the boat moves in a straight line. It is the wrong choice in several common situations. In less than about 20 ft of water, the ball is close to the boat and the bottom, and the strike zone can be covered with a diving lure or a weighted bait without the hardware. Over rocky, snaggy bottom, a ball that touches down can wedge, and the resulting load is taken by the boom and the hull. In strong current, the ball is swept aft and the angle correction becomes large and unstable. In a kayak or a small open boat, that same ball, boom and retrieval load become a stability problem rather than a fishing advantage. And in a spread that changes direction constantly, the cable and the fishing line cross more often than they do in a straight troll.

Maintenance and retirement

The service points are few and they are all load-bearing. Inspect the cable for kinks, meat hooks and flattened sections, and replace it on condition rather than on a calendar. Check the crimp or knot at the snap, and re-terminate if it has slipped. Wipe and lubricate the clutch and the swivel head, and rinse the unit after saltwater use without spraying water into the motor or the electronics. The stopper bead is a wear item. If it slips, the auto-stop either fails to trigger or triggers in the wrong place, and the ball comes up into the pulley. Replace beads that have hardened or moved. The circuit breaker is protection, not a retrieval limit: Scotty notes that a 15 A breaker can trip when lifting more than 20 lb from extreme depth, and that the correct response is to let it cool rather than to keep resetting it. A downrigger that is maintained is a depth tool. One that is not is a weight on a wire with an optimistic number on the counter.

Sources

  1. Magnum 10 STX, Magnum 10 STX TS, and Magnum 5 ST Features, Specifications and Manuals — Cannon Downriggers, Johnson Outdoors · T1
  2. Depthpower Electric Downrigger Manual — Scotty Fishing, Marine and Outdoors · T1
  3. Downrigger Fishing Angles for Salmon — Island Fisherman Magazine · T3