Three reads before you drop a jig on a mark

The mark sits 8 metres above a wreck and nothing eats the jig. Before the next drop, read three things: height off the structure, shape on the second pass, and whether the mark moves when the boat does. Those three reads set the jig, the depth and the drift.

boat
TargetsRed snapper
Watersaltwater
RegionsGulf of Mexico, Atlantic Ocean
Methodsjigging, bottom fishing
Quick answer

Measure the mark's height above structure, confirm it repeats on three passes, then match jig weight and fall count to that band rather than to the bottom.

How high off the bottom is the mark?

Height above the bottom is the read that decides everything else, and it is the one most anglers estimate rather than measure. On a sounder with a 60 m range, the gap between the top of the wreck and the tightest cluster of marks is the number that matters. If the cluster sits 8 to 12 m up, the fish are suspended and a jig that ticks the wreck on every drop is fishing below them. If the cluster is inside 2 m of the structure, the fish are holding on it and a slow lift off the bottom is the right presentation.

Translate that gap into a fall time before the first drop. A 200 g jig on 30 lb braid falls at roughly 1.0 to 1.5 m/s in still water, faster with current and slower with a wide, light jig. Twelve metres of gap is therefore 8 to 12 seconds of fall. Counting to that number and stopping the drop inside the band is a different technique from dropping to the bottom and winding up. The count is calibrated once per trip against a known depth, then trusted for the rest of it.

Species behaviour sets the expected height. NOAA's account of greater amberjack places adults on reefs, wrecks and rocky outcrops from about 18 to 73 m, often well above the structure rather than on it, which is why a wreck in 68 m can carry fish at 45 m. Snapper and grouper are more bottom-oriented, but even they rise 3 to 6 m off a wreck in current. Reading the height as a species clue is unreliable, but reading it as a presentation instruction is not: the top of the mark is where the lure should enter.

Do not confuse the wreck's plume with fish. A steel wreck in current produces a soft, rising return that starts at the structure and fades upward, and on a low-gain setting it can look like a column of fish. The plume has no hard edges and does not break into individual marks. Turn the gain up one step; a real school separates into distinct blobs, while the plume thickens evenly. If the return still looks like smoke after the gain change, treat it as structure.

Pass-to-pass changes in the same mark

A transducer does not see a point, it sees a cone. At 200 kHz the common beam is about 12 degrees wide, which at 60 m of depth is a circle roughly 12.6 m across. At 50 kHz a 45-degree beam covers about 50 m at the same depth. The same school therefore looks tight and tall on high frequency and wide and soft on low frequency, and a mark that seems to move between passes may simply be a different part of the school entering a different beam. Beam width, cone angle and what the screen does with them are covered in reading a sounder.

Boat movement adds the second variable. In 0.5 to 1.5 knots of drift, a 30-second pass covers 8 to 23 m, so the second pass is looking at a different slice of the wreck. A mark that appears on one pass and not the next may be real and local, or it may be outside the cone. The test is to run the same line three times instead of three different lines. Three passes on the same heading, with the same range and gain, produce a mark that repeats within about 2 m of depth; anything less consistent is noise, weed or a fish that moved.

Scroll speed affects the shape as much as the beam does. At a fast scroll the arches stretch and the bait appears as thin vertical streaks; at a slow scroll the same returns compress into blobs. The display changed; the water did not. Pick one scroll speed for the day and read the shape against it. The most useful habit is to photograph the screen on the first pass and compare the second pass against the photo, because memory tends to reshape what the screen showed.

Depth range is the other silent variable. An auto-range setting that jumps between 50 and 80 m changes the scale of every mark on the screen and makes the second pass incomparable to the first. Lock the range at about 1.5 times the depth, and lock the gain manually once the bottom return shows a hard, thin line with a small second echo. Auto settings are for finding structure; manual settings are for deciding where to drop.

From mark shape to jig weight

Depth sets the minimum weight needed to reach the fish; current sets the shape that keeps the line vertical. With the fish at 45 m and under 1 knot of current, 150 to 200 g gets there in 30 to 45 seconds and stays in contact. With 1 to 1.5 knots, the same weight sweeps 15 to 20 m downstream during the fall, and the jig arrives at the wrong place even though the count was right. The mark does not change; the water does, and the weight has to answer the water.

Read the drift before the drop. A 30-second drift with the boat broadside to the current gives the speed directly, and the line angle during the first drop confirms it. A line entering the water at 20 degrees off vertical is sweeping; at 5 degrees it is close to vertical. For the sweeping case, add 40 to 60 g or switch to a narrower jig that cuts down through the water instead of sailing. For the vertical case, a flatter jig that falls slower keeps the lure in the band longer.

The mark's thickness tells you how long the jig needs to stay in it. A band 3 m thick is crossed in 2 to 3 seconds at 1.2 m/s, which is barely one lift-and-drop cycle. A band 10 m thick gives three or four cycles. If the band is thin, slow the fall with a wider jig or a braked reel rather than adding weight; a heavier jig crosses the only productive water faster. If the band is thick, weight matters less than the cadence, and the count only needs to reach the top of it.

One calibration run per trip is enough. Drop on flat ground in the same depth, count from splash to the first bottom tick, and repeat twice. Three counts that agree within two seconds give a rate you can use all day. Rewrite that rate whenever the current changes by about 0.5 knots, because the fall time changes with it and a count that was right at slack water will be short by several seconds an hour later. A gain setting that repeats is the other half of that baseline; see sonar gain setup.

When is bait the reason to stop?

A bait ball is not a fishing mark, it is a reason to look for one. Dense bait shows as a solid, often red or dark mass with a hard top and a ragged bottom, and predators usually sit under it or on its edge rather than inside it. Stopping on the middle of the ball and dropping through it puts the jig in the one place the fish are not. The productive drop is on the down-current edge, where bait is being compressed and disoriented, or directly under the ball where the larger marks sit.

Size the bait before you commit. A ball 20 m across and 8 m thick holds enough forage to keep a school of amberjack fed for hours, and a jig that looks nothing like the bait is a hard sell. A ball 5 m across with scattered marks beneath it is a different situation: the bait is being held rather than grazed, and the predators are active. The difference shows in the shape of the bottom of the ball; a flat, hard bottom edge means the ball is being pushed up by fish below.

Three drifts is the decision point. If three passes over a confirmed bait ball produce no follows on a jig worked at the right depth, the fish are not feeding on that bait or the bait is not the reason they are there. Move 0.5 to 1 nautical mile and look for another ball, preferably one with bird activity or with a temperature break nearby. Returning to the same ball an hour later is worth one more drift, because bait balls move with the tide and the fish often follow them rather than the other way round.

Bait on the sounder and bait on the surface are two different reads. A ball that stays 20 m down at midday and rises to 8 m at dusk is following a light or a current cycle, and the predators usually follow the rise. The timing pattern is worth noting in the log. A ball that is pinned to the bottom in 60 m with no rise all day is often a refuge rather than a feed, and fishing it hard is a low-percentage use of the afternoon.

What does a blank screen after three passes mean?

A blank screen over known structure usually means the boat is not over the structure. GPS marks drift by 10 to 30 m between datum versions, and a wreck that is 25 m long can sit entirely outside a 12-degree cone at 60 m if the boat is 20 m off. The first correction is to widen the search: switch to 50 kHz, run a box pattern 100 m on a side around the mark, and watch for the hard bottom return rather than for fish. Finding the structure again is a navigation problem more than a fishing one.

If the structure is confirmed and the screen stays empty, the fish may be tight to it. A wreck with a strong return can hide fish inside the top 2 m of the return, especially on a high-gain setting where the structure blooms upward. Reduce gain until the bottom line is thin and look for marks breaking the top edge. Dropping a jig and counting the fall is the other test: a jig that stops early is landing on structure the screen says is not there, and that is useful information.

Tide stage explains a lot of blank screens. Slack water stacks fish tight to structure and reduces the current shadow that suspends them, so the same wreck can show a tall layer at 1 knot and a flat line at slack. If the screen goes blank as the tide dies, the fish have not left; they have moved down and tightened up. Change from a slow, wide jig to a heavy, compact one once the count stretches out and fish the last 5 m above the structure deliberately.

Three passes with nothing on the screen and nothing on the jig is the point to leave. A blank over good structure in good conditions is a stronger signal than a bad mark, because it removes the excuse of a bad presentation. Note the state of the tide and the time, run 1 to 2 nautical miles to the next piece of structure, and come back on the next tide rather than grinding the same wreck. The log entry is worth more than the fourth pass.

Short version

  • Measure the gap between the top of the mark and the structure, convert it to seconds of fall, and stop the drop inside the band.
  • Three passes on the same heading with a locked range and manual gain separate a real layer from weed, plume and a fish that moved.
  • Bait is a reason to fish the edge or the water beneath it, not the middle; three drifts without a follow is the cue to move a mile.

Sources

  1. What is sonar? — NOAA National Ocean Service · T1
  2. Greater Amberjack — NOAA Fisheries · T1
  3. What is a thermocline? — NOAA National Ocean Service · T1
  4. Marine electronics product library — Garmin · T2
Reading a Sounder: Hard Bottom, Arches and Bait
Counting the fall is how you reach the amberjack layer
Depth Sets Metal Jig Weight, Body Sets the Fall