Gain raises both signal and noise; set it on the bottom line

Two boats pass the same wreck at the same speed. One shows a clean bottom line and three separate fish above it. The other shows a bright band, a fuzzy skirt and a screen full of snow. The difference is one setting, and it is not the brightness dial.

electronics
TargetsGiant trevally
Watersaltwater
Regionsglobal
Methodsjigging, bottom fishing
Quick answer

Gain amplifies signal and noise together. Raise it until noise appears, back off one step, then confirm the bottom is still a line.

Gain amplifies signal and noise together

Reading what the echoes mean, from hard bottom to arches to bait, is covered in the guide to reading a sounder. This article stays on the setting that decides which of those echoes reach the screen at all. Gain sets the sensitivity of the receiver and the threshold above which a return is drawn. Turn it up and weak returns appear; the random energy in the water appears with them, because the display cannot tell a fish from a bubble of the same strength.

Garmin's echo 100 series manual puts it in one sentence: the gain setting controls the sensitivity of the sonar receiver to compensate for water depth and water clarity, increasing it shows more detail, and decreasing it reduces screen clutter. The same manual notes that a change made on one page applies to all pages, so a split screen is not a safe place to tune one side.

Furuno's FCV-688 guide draws the same line from a different design. Gain adjusts sensitivity over the entire screen, while interference, low-level noise and weak echoes each have a separate control. If your unit splits those jobs, use them: filtering noise is not the same act as lowering gain, and a unit with only one slider forces you to trade detail for a clean screen.

Gain is not brightness, and this is where most setups go wrong. Brightness and contrast change how the existing picture is lit. Gain changes which returns are in the picture. A dim screen with correct gain still shows a bottom line and separated fish; a bright screen with too much gain shows a glowing band and no fish at all. Garmin's LiveScope support article says the quiet part out loud: there is no single correct gain value, and the goal is a balance where the targets you want are clear without excessive clutter.

When auto gain loses the bottom

Auto gain is a control loop, and it is good at what it was designed for. Garmin's manual lists three modes with different targets: Auto-High displays weaker returns with more noise, Auto-Med displays medium-sensitivity returns with moderate noise, and Auto-Low displays lower-sensitivity returns with less noise. On flat mud or sand at a constant depth, any of the three will keep a readable picture while you watch bait in the top 20 m. Auto mode was built for that case.

It stops being reliable when the ground changes faster than the loop can follow. A thin hard layer over mud, a rock rising from sand, or a wreck edge at 40 m all change the strength of the bottom return within a boat length, and the auto circuit responds by re-scaling. What you see is a bottom that thickens and thins for no reason, and fish sitting within 2 m of it disappear into the correction. The same happens in 60 m and deeper, where the loop keeps lifting gain to hold the bottom and pulls up noise with it.

Simrad's guidance on traditional sonar is blunt about the limit: too much gain clutters the screen, too little hides fish, and the right setting depends on water clarity and depth. NOAA's acoustic survey calibration works from the same principle: adjust the echosounder against a standard target in water that is otherwise empty, so the setting reflects the system. The screen is describing a manual decision. Auto is a starting point and a convenience on featureless ground; it is not a substitute for looking at the bottom line and deciding whether you believe it.

There is also a propagation trap. On units that share one gain value across pages, an adjustment made for a deep page changes the shallow page too, and a setting made for mud follows you to rock. If the picture looks wrong after a move and you did not touch anything, check whether an earlier adjustment is still applied everywhere.

A three-step manual routine

Step one is to suppress noise, and the Garmin and Simrad manuals describe the same motion. Garmin says to raise the gain until noise begins to appear in the water portion of the screen, then decrease it slightly. Simrad says to increase gain until a small amount of background noise appears, then reduce it slightly, so subtle targets are detected without clutter. The whole calibration is this: find the noise floor, then step back below it. On most units that is one or two presses of the adjust key.

Step two is to lift the target. Drop a jig or a metal to a known depth on a tight line and watch it on the way down. At correct gain it is a distinct short mark that you can follow. The mark-reading guide takes that distinction further.; at too much gain it smears into a vertical streak that merges with the noise behind it. Do this over 15 to 20 m of water first, because a target that is easy to see in the shallows is easy to lose in 50 m if the gain is wrong.

Step three is to read the bottom. A correctly set bottom is a line with a clean lower edge. If it has grown a fuzzy skirt, or if the trace is two or three times its normal thickness on screen, the gain is above the point where the bottom is useful. Back off one more step and check whether a fish 1 to 2 m off the bottom separates from the trace. That single test decides whether the setting is right for jigging near structure.

Work an example. Over mud in 40 m at 1 kt of drift, raise gain until speckle appears, then back off one step and log it. Move to rock in 18 m: the return is far stronger, so back off two more steps from that setting. If you carry the 40 m mud setting to 18 m of rock, the bottom band swells and any fish holding tight to the reef is inside the band. The number did not change; the ground did.

Three signs the gain is too high

The first sign is a band of speckle across the top of the water column. As a working rule, when random noise fills roughly the top 10 to 15% of the screen at a normal range setting, the gain is above the useful threshold. That band hides bait in the top 10 m, which is exactly where bait often sits at dawn. Backing off one step usually clears the band and leaves the bait visible as a soft smudge instead of a snowstorm.

The second sign is a bottom that has become a band with a skirt, often with a false second echo beneath it. Some of that is real physics, and the reading guide explains how to tell a multiple from a real second feature. The gain problem is different. When the skirt appears over mud that showed a clean line an hour earlier, the setting has drifted above the ground it is trying to describe, and fish within 2 m of the bottom are now inside the trace.

The third sign is mid-water speckle that has merged into a continuous smudge. A single large fish should stand out as one mark among smaller ones; at excessive gain the background fills in around it and the mark becomes part of the texture. Garmin's LiveScope article lists the same effect from the other direction, noting that higher gain makes suspended particles more noticeable and the display look overly busy. In dirty water after rain, the gain is creating a problem that looks like fish.

Prop wash, rain and a choppy surface add their own noise near the top of the column, and no gain setting removes it. In those conditions the bottom trace stays readable longer than the mid-water picture, so set the gain for the bottom and accept a noisy top. Turning gain down until the top is clean usually costs the bottom detail you actually need.

How depth and bottom type shift the setting

The directions are consistent across manuals even where the scales are not. Deeper water needs more gain because the return is weaker and the receiver has to work harder. Hard ground needs less gain because rock and packed sand return a large share of the pulse. Mud and silt need more, because they absorb and scatter energy. Shallow water needs less than deep water at the same bottom type, because the bottom is closer and its return is stronger.

Express the adjustments as steps from a baseline. With a working setting for 30 to 50 m over mud, try one step less for 30 to 50 m over sand, and two steps less for 10 to 20 m over rock. For 60 to 80 m over sand, try one step more. For water full of suspended sediment after rain, try one step less, because the particles are the brightest thing in the column and gain only makes them brighter. All of these are working rules to test on the screen, and the test is always the same: does the bottom stay a line?

No honest article can give you a gain value to type in. Units differ in how they number the scale, transducers differ in output and cone angle, and installation changes the noise floor. Garmin's manuals describe raising and lowering sensitivity against the appearance of noise. A setting copied from another boat is a setting for another transducer, another hull and another day.

Use a reference instead of a number. Pick one piece of ground you know, such as a wreck at a known depth, and tune there until the bottom is a line and a jig at mid-depth is a separate mark. Write down the step count relative to your unit's midpoint, then use that as the baseline for the day. When the picture stops matching, return to the reference and start again.

Saving a preset and re-checking after a move

Save a preset for each ground type you fish, and name it by depth and bottom rather than by spot: 40 m mud, 20 m rock, 70 m sand. Names built from spot names stop meaning anything when you fish a new area, and they encourage carrying a setting into water it was never tuned for. Two or three presets cover most coastal fishing, and a fourth for dirty water after rain is worth having.

Re-check the setting when any of four things change: depth by more than 15 m, position by more than 5 nm, water clarity after rain or a tide change, or the transducer angle after someone leans on the bracket. Each of those changes the strength of the return, and the setting that was right before the change is now a guess. The check takes three passes over the same line with the gain fixed, which is also the test for whether a mark is real.

The common failure is copying a screenshot. A photograph of someone else's screen carries their unit, their transducer, their mounting angle and their water, and none of that transfers. The second common failure is tuning on a drifting boat and then wondering why the picture changed when the boat stopped: motion changes how marks are drawn, and a setting tuned at 2 kt can look wrong at rest even when the gain is correct.

Verify with the bottom. A gain setting that draws a thin bottom line, separates a jig at mid-depth and leaves the top of the column mostly clean is right for that ground, whatever the number says. If a mark repeats on three passes at that setting, the setting is doing its job. If it appears once and vanishes, the gain is producing it.

Short version

  • Gain raises returns and noise together, so the correct setting is the one just below the noise floor.
  • Auto gain is fine on flat ground at constant depth; it hides the bottom where hardness or depth changes within a boat length.
  • Raise until speckle appears, back off one step, then confirm the bottom is a line and a mid-water jig is a separate mark.
  • Adjust in steps from a baseline by depth and bottom type; copy no numbers between boats or units.

Sources

  1. echo 100 Series Owner's Manual — Garmin · T2
  2. GPSMAP 10x2/12x2 Series Owner's Manual: Adjusting the Level of Detail — Garmin · T2
  3. Settings for Improving Garmin LiveScope Image Quality — Garmin Support · T2
  4. FISH FINDER Model FCV-688 Operator's Guide — Furuno Electric · T2
  5. Traditional Sonar: How to Read It Like a Pro — Simrad Yachting · T2
  6. Acoustic Hake Survey Methods on the West Coast: Echo Sounder Calibration — NOAA Fisheries · T1
Reading a Sounder: Hard Bottom, Arches and Bait
Counting the fall is how you reach the amberjack layer