A 300 m drop costs roughly 0.4-0.6 Ah on a 12 volt reel, so a 20 Ah lithium pack covers a normal day with reserve. The label is not the number that matters; usable capacity and voltage under load are.
What Happens to 100 Ah at the Reel
Amp-hours are measured at a slow, steady discharge, usually over 20 hours. An electric reel does the opposite: it pulls 6-12 amps in bursts, with spikes when a fish surges. Lead-acid batteries lose usable capacity as the draw rises, a relationship described by Peukert's exponent. A 100 Ah lead-acid battery that delivers 100 Ah at 5 amps may deliver 70-80 Ah at 20 amps, and it should not be discharged below 50 percent if it is to survive more than a season.
The practical result is that a 100 Ah lead-acid pack is a 50 Ah pack for planning purposes, and a 40 Ah pack on a cold morning. Lithium iron phosphate (LiFePO4) holds voltage better under load and can use 90-100 percent of its rating, which is why a 20 Ah lithium pack can outperform a 40 Ah lead-acid one in a deep-drop application. The chemistry matters more than the number printed on the case.
Voltage sag is the second hidden loss. A lead-acid pack at rest may read 12.7 volts; under a 30 amp load it can drop to 10.5-11 volts. The reel sees the lower voltage, slows down and pulls more current for the same work, which drains the pack faster and heats the motor. A lithium pack sags less, so the reel keeps its speed until the battery is nearly empty, which is safer but also less warning.
The third loss is wiring. A 3 percent voltage drop across a long, thin cable is 0.36 volts at 12 volts, and at 30 amps that is 10 watts of heat in the cable instead of the motor. Short, thick leads and clean terminals are worth more than another 5 Ah of capacity, especially on a boat where the battery sits at the transom and the reel is at the bow.
Amp-Hours per 300 m Retrieve
Worked example: a 12 volt reel retrieves 300 m at about 1 m per second, so the motor runs for 5 minutes, or 0.083 hours. If the average draw is 6 amps, the energy used is 6 × 0.083 = 0.5 Ah. A 20 Ah lithium pack therefore has a theoretical 40 drops, before reserve, before current, and before the fish that adds 10 amps for the last 100 m.
The load changes the number more than the depth does. A bare 8 lb lead at 300 m may draw 4-6 amps; a 20 lb grouper plus the lead in 1 knot of current can push 15-20 amps for several minutes, which is 1.5-2.5 Ah for a single retrieve. Three big fish in a day can use more capacity than thirty empty drops. Budgeting on drop count alone underestimates the days that matter.
Swordfishing is the extreme case. A 500 m drop with heavy lead and a fish can run 8-12 amps and 50-75 minutes of total motor time across a day, which is 5-9 Ah before spikes. That is still within a 10-20 Ah lithium pack for a normal 4-6 drop day, but it leaves little margin for a second angler or a battery that started the day at 60 percent.
The arithmetic is only a starting point because the reel does not draw a constant current. The first 30 m of a retrieve lifts the lead and the fish against the most line drag; the last 30 m is mostly the fish. A pack sized on the average will be marginal on the peaks, which is why the reserve should be 30-50 percent rather than 10.
Depth, Current and Amp Draw
Current draws more, and it does so in a way that is hard to feel from the helm. A 300 m retrieve in slack water with a 6 lb lead is a light load. The same retrieve with the boat drifting away from the fish at 1 knot puts the line at an angle, and the motor is now pulling the rig sideways through the water as well as upward. The amp draw can double without the depth changing by a metre.
Line diameter is the second lever. A 0.50 mm braid at 300 m presents more surface to the current than a 0.42 mm braid, and the motor pays for it on every retrieve. This is the same trade-off described in deep-dropping rigging: thinner braid reaches bottom with less lead, and it also retrieves with less current load. The limit is abrasion, not the meter.
Boat handling is the third. Keeping the boat over the fish for the first 50 m, then drifting with it, reduces the angle and the load. A captain who motors away from a hooked fish to chase a different mark turns a 0.5 Ah retrieve into a 1.2 Ah one, and the battery pays for the decision. On a 20 Ah pack, the difference is between 40 drops and 16.
Temperature is the fourth. A lithium pack loses capacity in cold weather, and a lead-acid pack loses both capacity and cranking ability. A pack stored in an unheated locker overnight at 5°C may deliver 80 percent of its warm-weather capacity; the same pack warmed in the cabin before the trip delivers more. Keeping the battery out of the cold is free capacity.
Sizing the Pack and Wiring
Start with the daily energy budget rather than the drop count. Estimate the number of retrieves, the average motor-on minutes per retrieve and the average amps, then add 30-50 percent. A day of 15 drops at 300 m, 5 minutes each at 8 amps average, uses 10 Ah; with reserve, a 15-20 Ah pack is right. A sword day with 6 deep drops at 12 amps and 10 minutes each uses 12 Ah before spikes, so a 20 Ah pack is the minimum.
Fuse the circuit at the battery rather than at the reel. A 40 amp fuse or breaker protects the wiring against a stalled motor and a short, and it should be within 30 cm of the positive terminal. The Lindgren-Pitman LP SV-1200 lists a maximum 30 amp draw, so a 40 amp fuse gives headroom without allowing a dead short to weld the cable to the terminal.
Cable gauge should keep voltage drop under 3 percent at the working current. For a 12 volt system drawing 30 amps over a 3 m run, that means 6 AWG or heavier; over 6 m, 4 AWG. The exact number depends on the round-trip length and the acceptable drop, but the principle is simple: the cable is part of the circuit, and a thin cable is a heater.
Carry a second pack rather than a giant one. A 20 Ah pack that weighs 3 kg can be swapped in a minute; a 60 Ah pack that weighs 9 kg is a permanent installation with a single point of failure. Redundancy matters 40 miles offshore, and two packs also let one charge while the other fishes.
Measure the draw once instead of guessing. A clamp meter on the positive lead, read during a normal retrieve and again during a hard one, gives the two numbers the budget needs. Most crews find that the average is lower than they feared and the peak is higher, which is exactly why the fuse and the cable deserve as much attention as the amp-hour rating.
The Reel Slows Before the Pack Is Empty
The reel slows because the voltage at the motor has dropped rather than because the amp-hours are gone. A lead-acid pack at 50 percent state of charge can still light a cabin, but under a 20 amp load it may fall below the reel's low-voltage cutoff. The motor stops with the fish still 200 m down, and the angler concludes the battery is dead when it is merely sagging.
The failure mode is predictable. The first retrieves are normal, the fifth is slightly slower, and the eighth triggers a reset or a shutdown at the worst moment. A voltage display on the reel or a small voltmeter at the battery turns that surprise into a warning: when the pack falls below 11.5 volts under load, the next drop should be shallower or the pack should be swapped.
Cold and corrosion make it worse. A terminal with a film of salt and a loose clamp adds resistance exactly where the current is highest, and the voltage at the reel drops before the battery does. Cleaning the terminals and checking the clamp torque at the start of each trip is a two-minute job that prevents most mid-retrieve shutdowns.
The last cause is a stalled motor, which is not a battery problem at all. If the rig is hung on the bottom and the angler keeps the reel engaged, the motor draws its maximum current and the protection circuit cuts out. The fix is to slack off, let the boat move, and try a different angle rather than holding the button and hoping.
A battery management system adds one more layer. Most lithium packs shut off at a low-voltage threshold to protect the cells, and that threshold can be reached under a spike even when the pack still has 20 percent capacity. The reel stops, the display goes dark, and the pack recovers to 12.5 volts a minute later. That is not a dead battery; it is a BMS doing its job, and the correct response is a lighter retrieve rather than a deeper drop.
Charging and Storing a Pack
LiFePO4 packs prefer to be stored at 50-80 percent charge rather than full or empty. A pack left at 100 percent in a hot locker loses capacity faster than one stored at 70 percent. Lead-acid is the opposite: it should be stored fully charged, because a partially charged lead-acid battery sulfates and loses capacity permanently.
Charging current should be matched to the pack. A 20 Ah lithium pack is happy at 10 amps (0.5C) and will recharge in about two hours; a 100 Ah lead-acid pack wants 10-20 amps and takes most of a night. A charger that is too small is slow but safe; one that is too large can overheat a small pack, especially if it has no balancing stage.
Balance and inspection are annual tasks. Lithium packs with a built-in BMS balance the cells automatically, but a pack that has been deeply discharged may need a wake-up charge before the BMS will accept current. Lead-acid packs need the terminals cleaned, the electrolyte checked if they are serviceable, and a load test at the start of the season.
The capacity you plan with should be the capacity you measured, not the capacity on the label. A load test at the working current, run until the low-voltage cutoff, gives a real number in amp-hours. A pack that measured 18 Ah when new and measures 12 Ah two seasons later is still useful, but it is no longer a 20 Ah pack for planning purposes.
Short version
- Plan on usable amp-hours: 90-100 percent for lithium, about 50 percent for lead-acid.
- Budget 0.4-0.6 Ah per 300 m retrieve, and double it when current or a big fish is involved.
- Fuse at the battery and size cable for under 3 percent voltage drop at 30 amps.
- Watch voltage under load; a reel that slows at 11.5 volts is warning you before the pack is empty.
Sources
- Electric Fishing Reel Battery: The Complete Guide — Abyss Battery · T2
- LP SV-1200 Commercial Electric Reel Power Requirements — Crook and Crook · T2
- Tanacom 1200 Specifications — Daiwa US · T2
- Electric Reel Amp Draw: 12V vs 24V Sizing — Extreme Angler · T3
- Batteries — US Department of Energy, Office of Energy Efficiency and Renewable Energy · T1