Read a wreck on side-scan as four fishing zones

The image appears as a bright white shape with a long black tail, and every angler on the boat calls it the wreck. It is only the part that faces the transducer. The rest of the story is in the shadow, the scour and the debris field, and none of those show up as bright.

electronics
Targetssnapper, grouper, cod, amberjack
Watersaltwater
RegionsGlobal
Methodswreck fishing, drifting, jigging
Quick answer

Side-scan shows reflectance and shadow, not a photograph, so a wreck appears as four separate objects before it appears as a ship.

A side-scan image is a strip of reflectance

Side-scan shows reflectance and shadow, not a photograph, so a wreck appears as four separate objects before it appears as a ship. A side-scan transducer sends a fan-shaped pulse out to both sides and records the strength of the return, line by line, as the boat moves. NOAA's description is that the array sweeps the seafloor like a flashlight beam, and the vessel has to run straight lines at constant speed to build a usable image. The picture you see is not a photograph. It is a map of how hard and how rough each patch of bottom is.

That distinction explains most misreads. A bright return means a strong reflector: rock, steel, gravel, a swim bladder. A dark patch means weak return: mud, sand, weed. A shadow behind an object is empty water where the pulse could not reach. Garmin's own imagery documentation makes the same point from the mapping side, noting that stronger returns indicate harder bottom and are displayed as brighter colour.

Frequency sets the trade. Lower frequencies around 50 to 100 kHz reach further to each side and give a wider swath; higher frequencies give finer detail over a narrower strip. For wreck hunting, that is two different jobs: find the anomaly wide, then identify it narrow. One pass cannot do both well.

A wreck reads as four separate objects

A steel wreck that has been down for decades is not a ship any more. It is a hull, a scour pit, a debris field and a biological reef, and each one has a different acoustic signature.

The bow is usually the highest-contrast part, because it faces the prevailing current and presents a vertical face to the sound. In sand, the current also digs a scour pit around the bow, which shows as a dark crescent on the up-current side and a bright rim where the excavated sand piles up. That crescent is one of the most reliable wreck indicators on a featureless seabed.

The stern is where the debris trail starts. Anything that fell off, plus anything the current has moved, ends up down-current of the hull, and it shows as a scatter of small bright targets fading over 20 to 100 m. On older wrecks the trail can be longer than the hull itself. Fishing the trail is often better than fishing the hull, because the trail is lower, flatter and easier to present a bait on.

The sides are where the image lies. The side facing the track is bright and detailed. The side facing away is hidden in the acoustic shadow, so a wreck that looks like a half-ship on screen may be intact. If the shape matters, run a second pass from the opposite side. Two passes from opposite directions are the cheapest way to stop guessing.

Orientation is the other thing the image gives you for free. Most wrecks lie with the long axis across the current, because the hull settles into the stable position once it fills. If the long axis on screen runs north-south and your drift runs east-west, you will cross the wreck rather than travel along it, and every pass will be short. Rotate the plan, not the wreck: set up so the drift runs along the hull, even if that means starting 100 m off the bow and accepting a longer run-in.

The superstructure is the exception. A wheelhouse or a gun turret stands 3 to 8 m proud of the seabed and throws a shadow several times its height. That shadow is the easiest thing on the image to measure, and it is how you estimate how much structure you are actually looking at.

Range and gain for a first pass

Start wide: 40 to 60 m per side if the unit allows it. At that range the wreck is small on screen, but you can see the whole debris field in one frame and you will not drive past the edges of it. Run a straight line offset from the likely target rather than over it. Directly over the wreck, the hull sits in the transducer's near-field blind spot and the most important part of the return is missing. The gain setup guide explains why gain is not brightness.

Gain is the setting that ruins most images. Too little gain and hard bottom looks like soft bottom; too much and the water column fills with speckle that looks like bait. Set gain so that flat sand reads as a uniform mid-grey with a little texture, then leave it alone for the pass. Automatic modes tend to chase the bottom and change contrast between lines, which makes a wreck look like it is changing shape.

Pass spacing is the other number people get wrong. A practical rule is to space track lines at 50 to 70 percent of the total swath width, so adjacent images overlap. At 50 m per side (100 m swath), that means lines every 50 to 70 m. Wider spacing leaves a gap exactly where the wreck's debris trail runs.

Mark the first contact as a waypoint on the centre of the bright return, then mark the far edge of the debris trail as a second waypoint. Two points give you a heading and a length. One point gives you a circle you will spend an hour driving around.

Shadow tells you the shape

Brightness tells you the material. Shadow tells you the shape. The shadow is cast away from the track, so its direction on screen tells you which side of the object the sound came from, and its length is proportional to the object's height above the bottom.

That ratio is useful even without calibration. A shadow roughly as long as the object is wide suggests a low, flat structure: a barge, a landing craft, a collapsed hull. A shadow two to four times the object's visible width suggests something standing up: a wheelhouse, a crane, a rock pinnacle. A shadow that is broken into segments suggests a hull that has collapsed in the middle, with gaps between intact sections.

The shadow also hides fish. A fish sitting tight against the dark side of a wreck can be invisible on side-scan because it is inside the shadow. A sonar image that shows a clean hull and no fish therefore does not mean an empty wreck. It means the fish are on the side you cannot see, which is a useful piece of information in itself: fish the shadow side first.

One caution on scale. Shadow length changes with range and with the height of the transducer above the bottom, so the same wreck measured on two passes can give two different ratios. Use the shadow for relative comparisons within one image rather than as an absolute measurement across days.

Fish returns sit in a different part of the image. A fish in the water column shows as a small, isolated bright mark with no shadow, because there is nothing behind it to block the pulse. A fish tight on the bottom is harder: it merges into the bottom return and disappears. The marks you see above a wreck are therefore only the suspended fish, and the ones that matter on a slow tide may be the ones you cannot see at all. A vertical jig through the hull is still the test.

From sonar image to drift plan

The image gives you a long axis, a high side and a low side. The drift plan follows from those three facts. The three-pass wreck drift is the boat-handling half of this plan. In current, the boat will travel roughly along the current, so the ideal track is a line that starts up-current of the bow and passes along the long axis, giving the longest possible time over structure. If the current runs across the wreck, the drift lasts 20 to 30 seconds and the answer is a sea anchor or a jogging motor rather than a longer cast.

The high side is where the vertical face is, and vertical faces hold fish that suspend. The low side is where the debris is, and debris holds fish that sit on the bottom. Those are two different presentations: a jig or a live bait dropped down the face, versus a bait fished on a running ledger over the trail. Deciding which one before the boat arrives is what saves the first 10 minutes of a drift.

Record the pass. A screenshot with the range, gain and heading visible is worth more than a memory of it. The next time you come back, the wreck will look different because the light, the swell and the boat speed will be different, and the old image is the only baseline you have.

If the wreck is in 40 m or less and the visibility is decent, a side-scan image is also a safety document. It shows the highest point of the structure, which is what you need to know before you anchor or drift over it. A wreck that tops out at 22 m in 40 m of water is a different proposition from one that tops out at 34 m.

Anchoring on a wreck and drifting over it are two different uses of the same image. Anchoring needs the low, flat debris edge, because that is where an anchor will set without wedging in steel. Drifting needs the high side, because that is where the fish suspend. If the tide runs hard enough that a drift lasts under a minute, the anchor is the better tool, but then the image also has to tell you where the chain will lie. A 60 m swing over a wreck with 8 m of relief is how running rigs get cut.

What side-scan cannot tell you

It cannot tell you species, and it cannot tell you whether the marks above the wreck are fish or suspended weed. Small bright targets in the water column are ambiguous; a bait ball, a school of snapper and a cloud of jellyfish can all look similar. Treat them as a reason to drop a bait rather than as a reason to claim you have found fish.

It also cannot see through the thermocline or into a wreck's interior, and it does not measure height directly. Those are the jobs of down-scan, CHIRP and a vertical jig. Side-scan's real strength is coverage: it finds structure you did not know was there, and it shows the extent of the rubble around it. Everything after that needs a different tool.

The last limitation is legal rather than technical. A side-scan image is a map of someone else's wreck, and in many jurisdictions war graves and protected historic wrecks are closed to anchoring, potting and sometimes to fishing entirely. The image makes it easy to find them, which is exactly why the rule matters. Check the local protected-wreck list before the waypoint goes in the plotter rather than after.

The practical rule is to spend the first 20 minutes of any wreck day mapping rather than fishing. Two passes, one wide and one close, four waypoints (bow, stern, high side, debris edge), and a screenshot. That is enough to fish the wreck properly for the rest of the tide instead of driving over it and guessing.

Short version

  • Side-scan maps reflectivity and shadow, not species: bright means hard, dark means soft, long shadow means tall.
  • A wreck is four targets: bow scour, stern debris trail, high side, and rubble skirt. Mark each separately.
  • Run wide and offset first (40-60 m per side), then a close high-frequency pass from the opposite side to see what the shadow hides.
  • Space passes at 50-70 percent of swath width so the images overlap across the debris field.
  • Fish the high side with a vertical presentation and the debris trail with a bottom bait; expect fish to hide in the acoustic shadow.

Sources

  1. Exploration tools: side-scan sonar — NOAA Office of Ocean Exploration and Research · T1
  2. Remote sensing: why sound? — NOAA Office of Ocean Exploration and Research · T1
  3. ECHOMAP Ultra series owner's manual: SideVü sonar view — Garmin · T2
  4. Sonar imagery and bottom hardness — Garmin Marine · T2
Reading a Sounder: Hard Bottom, Arches and Bait
Three passes over a wreck, and when to stop
Three reads before you drop a jig on a mark