Kite fishing: 8-15 kt of wind and a 3 kg release clip

Kite fishing looks like a magic trick until the wind drops, the clip pops, or the two baits braid themselves together. It is really a wind problem and a tension problem, and both can be measured before you leave the dock.

kite
TargetsKing mackerel, Wahoo
Watersaltwater
RegionsAtlantic, Gulf of America, Indian Ocean
Methodskite, live bait, drift
Quick answer

Fly the kite in 8-15 kt of wind, keep the kite line at 45-60 degrees, and set the release clip to roughly 3 kg so a swimming bait stays put but a taking fish pulls free.

When does a kite beat a balloon

A kite and a helium balloon do the same job: hold a live bait at the surface away from the boat. The kite is better whenever there is enough wind to fly it, because it keeps the bait skipping and spraying rather than swimming in a fixed spot, and because you can steer it left and right by working the kite line.

That surface disturbance is the point. Sailfish, king mackerel and wahoo are built to attack bait that is being pushed along the surface, and a bait held just under the skin of the water leaves a wake that is visible from a long way off. Florida's FWC describes kite fishing with live goggle eyes or blue runners as one of the standard sailfish methods, alongside slow-trolled ballyhoo and hookless teasers.

The balloon wins when the wind is under about 5 kt, or when there is no wind at all and you still want a bait out wide. It cannot be steered, it drifts with the surface layer, and it does not produce the same surface action, but it will hold a bait in the air when a kite would be swimming in the water. The depth and drift side of that method is covered in live bait balloon depth.

Neither method changes your legal obligations. NOAA's Atlantic HMS rules require billfish that are not being kept to be released immediately without removing them from the water, even for a photo. Plan the release before the bite.

How much wind you actually need

The workable band is roughly 8-15 kt. Below 8 kt the kite flies but sags, the line angle falls toward 30 degrees, and the baits sit in the water instead of skimming. Above about 18-20 kt the kite becomes hard to control, it dives in gusts, and the clip tension that held a bait in 12 kt will start releasing on wave action alone.

Aim for a kite line angle of 45-60 degrees above the horizon with 100-200 ft of line out. That angle is the practical readout of whether the wind is doing its job. If you are paying out line and the angle keeps falling, you are not flying a kite, you are dragging one.

Wind direction matters as much as speed. You want the kite upwind of the boat so the baits work downwind through the area you are trying to fish. A beam wind pushes the whole spread sideways and the baits converge; a following wind puts the kite over the transom and the baits under the boat.

Check the forecast against the actual anemometer, and treat the app as a forecast. Wind at 10 m above the water is often stronger than what you feel on deck, and a forecast of 10 kt can be 6 kt at the surface in the lee of land. If the surface wind is marginal, fly one kite high and keep the baits light rather than committing two kites.

Sea state matters as much as the number. Eight knots over a long ocean swell is easy; eight knots against a steep chop is not, because the kite line loads and unloads with every wave and the baits get jerked at the surface. A short, steep sea also makes the boat roll, which swings the kite and changes the apparent wind at the same time. If the swell is over about 1.5 m and the period is short, fly higher and lighter, or fish a different method and keep the kites for the next day.

What release-clip tension holds a live bait?

The clip is a fuse. It has to be strong enough that a bait swimming at the surface does not trip it, and weak enough that a fish grabbing the bait pulls the line free instantly. Set it too light and the bait pops the clip every few minutes; set it too heavy and the fish feels the resistance and drops the bait.

Rough numbers for a 15-25 cm live bait: about 2-3 kg of release tension, measured with a small spring scale on the clip. Bait size drives the number, so a big goggle eye gets the upper end and a threadfin herring the lower. Test it by hanging the scale where the fishing line attaches and pulling slowly until the clip lets go.

Set the clip so the bait hangs with its head just under the surface and its back breaking the water. That attitude creates the wake and keeps the bait oriented into the wind. If the bait is buried, shorten the drop from the clip; if it is skipping clear of the water, lengthen it.

Clip position on the kite line is a separate setting. Space clips 15-22 m apart so a fish taking one bait does not cross the line of the other. Clips that are too close turn a double hookup into a single braided mess.

How do you set a two-bait spread without tangling?

Fly one kite until you can keep the first spread clean for an hour. Two kites double the surface area you cover and double the ways the lines can cross, and most of the tangles happen because the kites are flying at different angles rather than because the baits are too close.

Stagger the baits by depth and distance. Put the near clip at about 30 m from the boat and the far clip at 60 m, and set the near bait slightly deeper than the far one. When the boat swings on the drift, the two lines sweep different arcs instead of stacking on top of each other. The outrigger version of the same spread is covered in outrigger release and clear lines.

Keep the boat's bow into the wind and drift, rather than trying to motor with kites out. Engine wash and the boat's own drift change the apparent wind at the kite, and the kite responds by diving or circling. If you need to reposition, bring the baits in first, move, then re-deploy.

Watch the kite, not the baits. The kite tells you what the wind is doing two seconds before the baits do. A kite that starts to hunt left and right is about to cross lines; correct it with a small adjustment on the kite line before the spread folds.

Deploy in the same order every time. Kite up first, then the far clip, then the near clip, and only then the second bait. Each step is checked before the next one starts, so a problem with the kite is fixed while there is nothing else in the water. Doing it in a hurry, with one bait already swimming and the kite still climbing, is how a 15-second tangle turns into twenty minutes of re-rigging.

What happens when a fish eats?

The clip releases, the bait line goes slack, and the fish is now holding a bait with no tension on it. This is the moment to do nothing for a count of three to eight. The fish has to turn with the bait; setting the hook on the release drives the hook back out of its mouth.

Then engage the reel, come tight, and keep the rod low and pointed at the fish for the first run so the line is not sawing across the surface. If a second bait is still out, clear it: reel the kite down or pop the remaining clip so the fish does not wrap the kite line.

With circle hooks, do not strike at all. Come tight and let the fish load the rod. The hook rotates into the corner of the jaw as the fish turns away, which is exactly the geometry the hook was designed for, and it is also why NOAA's HMS guidance recommends circle hooks and dehooking tools for billfish.

Keep the fish in the water at boatside. NOAA's rule for Atlantic HMS is explicit: release immediately, do not remove the fish from the water even for a picture, and use a dehooking tool or cut the leader close if the hook cannot be backed out cleanly.

Shorten the fight where you can. Heavier tackle and a shorter leader bring the fish in faster and leave it with more energy for the release, which is the same advice NOAA gives for HMS generally. A sailfish that has been fought for 40 minutes on light line is a fish that is far less likely to swim away strongly, and the photograph is not worth that trade.

What goes wrong when the wind dies or builds

When the wind dies mid-drift, the kite stalls and starts to fall toward the water. Do not reel hard to keep it flying: take in line steadily until the angle recovers, or bring the spread in and switch to a balloon. A kite that hits the water is a kite that is now a sea anchor, and the baits will tangle around it within a minute.

When the wind builds past about 20 kt, the kite starts to dive in gusts and the clips release on wave shock. Add tension at the clip, shorten the drop to the bait, and consider flying the kite lower with less line out. If the gusts are sustained, take the kite down. The spread is not worth a lost fish and a lost kite.

Rain and squalls are the third failure. A wet kite flies heavier and a front that passes overhead can shift the wind 90 degrees in a few minutes. Watch the water to windward; dark patches and a visible gust line give you two or three minutes to get the baits in. The rule that covers all three cases is that the kite is a wind instrument: if the wind is not in the 8-15 kt band, pick a different method rather than fighting the kite. Teaser-and-switch trolling works in the calm and the blow, and it uses the same live baits and the same release discipline.

Keep the baits working. A kite bait that has been in the water for ten minutes without moving is a bait that has swum itself into a circle and is now sitting under the boat. Ease the kite line out a metre or two every few minutes so the baits slide downwind through fresh water, and watch the wake to confirm both baits are still tracking straight.

Bringing the kite down is a skill of its own. Reel steadily with the rod tip following the kite, and have one person tail the line so it does not loop into the props. Do not grab the kite line with a bare hand when a gust hits; let the reel take the load. A kite retrieved under control at the end of the trip is the reason you can fly it again tomorrow.

Short version

  • Kite fishing works in an 8-15 kt wind band; outside it, switch to a balloon or to teaser trolling.
  • Set release clips to about 2-3 kg for 15-25 cm live baits and space them 15-22 m apart on the kite line.
  • On the bite, wait 3-8 seconds, come tight without striking, and keep billfish in the water for release.

Sources

  1. Sailfish: State's Saltwater Fish Offers On-the-Water Excitement — Florida Fish and Wildlife Conservation Commission · T1
  2. HMS Compliance Guide: Recreational Fishing Guide for Atlantic Tunas, Swordfish, Shark and Billfish Regulations — NOAA Fisheries, Atlantic Highly Migratory Species Management Division · T1
  3. Tigress Kite Release Clip — Tigress Outriggers & Gear · T2
  4. Kite Fishing Guide: Setup, Technique and Tips — Tackle Room · T3
A Balloon Stopper Sets Where the Live Bait Swims
An outrigger clip set for a skirt will drop a live bait
Set Trolling Spread Geometry Before Lures