Teaser and dredge: pull fish up, then feed the hooked bait

A dredge is not a lure. It is a moving school of fake bait whose only job is to pull fish into the top few metres, where a hooked bait is waiting. Most failed switches are not missed strikes; they are baits that were never in the right place.

trolling
TargetsBlue marlin
Watersaltwater
RegionsAtlantic, Gulf of America, Pacific
Methodstrolling, teaser, switch bait
Quick answer

Run the dredge 8-10 lb of lead and 30-50 ft back, keep it 10-20 ft down, and put the hooked bait 20-40 ft behind it so a rising fish meets the bait, not the frame.

What a dredge imitates

A dredge is an umbrella-shaped frame carrying a dozen or more baitfish imitations on each tier, towed below the surface so it reads as a dense school. Stack two or three tiers and the silhouette becomes a baitball rather than a line of individual fish. That density is the whole idea: a billfish investigating a school is a fish that has stopped hunting and started looking.

The frame matters less than the silhouette. Holographic strips, plastic mullet and natural baits all work because they produce a broad, flickering mass with no single target in it. A predator that fixes on one bait in the school is doing exactly what you want, because the one bait it can catch is on a hook behind the dredge.

A dredge is no substitute for a spread. It has no hook, it is not meant to be eaten, and it is towed where you cannot strike. Treat it as a herding tool and the rest of the spread makes sense.

Florida's FWC describes the same idea in its sailfish advice: trolling with hookless bait and teasers, then casting to fish as they appear in the spread. The teaser creates the opportunity; the cast bait converts it.

How deep and how far back should it run?

The working range is 10-20 ft down and 30-50 ft behind the transom. Deeper than about 25 ft and the fish may come up under the boat without ever seeing a bait; shallower than 8 ft and the dredge breaks the surface in a chop, which spooks rather than attracts.

Depth comes from lead ahead of the dredge rather than from the frame. A 6-10 ft length of cable or heavy mono ahead of the dredge with an 8-10 lb trolling weight gets it down and keeps it there at 7-8 kt. Tournament boats often add chin weights to the individual baits as well, which keeps the whole mass tracking without spinning.

Distance is a function of speed. At 7 kt, 30-50 ft behind the boat puts the dredge in clean water outside the prop wash. At 9 kt the same dredge rides higher and further back, so add weight or shorten the drop. Watch the tips of the frame on the sounder or with a camera; if they are curling, the dredge is planing and the silhouette is wrong. Speed selection for the spread is covered in trolling speed and bait action.

Two dredges, one each side, should run at slightly different depths. A pair at the same depth and distance will cross on every turn. Put the windward dredge 3-5 ft shallower so the lines separate when the boat swings.

The retrieval system matters when the day ends and a fish is still on. A dedicated electric reel on a short, stiff rod with a pulley at the transom lets one person bring a loaded dredge in without a fight. Tournament boats run the dredge line through a pulley near the outrigger so the load stays off the rod tip. If you are pulling a 12-bait frame by hand while a fish is on, you are not fishing any more.

Keep the dredge line separate from the fishing lines. A dredge on a planer or a downrigger cable that runs near a flat line will take the flat line with it when it comes up. Colour-code the dredge line and brief the crew on which line is which before the first set.

Where the hooked bait sits relative to the teaser

The hooked bait belongs behind and slightly above the dredge, at the depth a rising fish will pass through. Twenty to forty feet behind the frame is the usual starting point, with the bait swimming at 5-10 ft. That puts the bait on the fish's path as it comes up to look at the school, rather than off to one side where it is never seen.

Distance from the boat matters as much as distance from the dredge. A bait 100 ft back is a long cast for a nervous fish and a long fight on light tackle; a bait 30 ft back is in the prop wash. The compromise is 50-80 ft, which is close enough to control and far enough to look natural.

Flat lines and outrigger lines do different jobs. The flat line is the close-range switch bait, and the outrigger bait is the one that gets seen from further away. When a fish appears on the dredge, the flat line is usually the one you feed, because it can be dropped back into the fish's path in seconds. The release-clip and clear-lines side of that split is covered in outrigger release and clear lines.

Keep one bait on a conventional reel with the drag set and the clicker off, ready to free-spool. The switch takes seconds, and a bait that has to be untangled from a clip first is a bait that arrives late.

Match the bait to the dredge rather than to your favourite lure. A dredge of 15 cm mullet pulls fish that expect 15 cm bait, and a 30 cm skipping bait behind it looks wrong. Run the switch bait at roughly the size and colour of the baits in the frame, and keep a second rod rigged with a smaller bait for fish that hang back and refuse the big one.

Watch the angle of the dredge line as closely as the dredge itself. A line that is running nearly vertical means the dredge is directly under the boat with very little swing; a line at 30-40 degrees behind the transom means it is tracking properly. That angle is the quickest diagnostic you have when the boat changes speed or a current line hits the spread.

How do you make the switch without losing the fish?

The switch is a timing problem more than a casting problem. When a fish shows on the teaser, the boat keeps moving, the teaser keeps pulling, and the hooked bait is free-spooled back until it sits where the teaser was. The fish turns from the fake school to the real bait because the real bait is now the easiest meal in the same place.

Free-spool with your thumb on the spool and keep the drag out of it. Let the bait run back 50-100 ft with the boat still in gear, then engage the drag and let the line come tight as the boat moves away. That is what makes the bait look like a straggler dropping out of the school.

Do not strike a billfish on the drop-back. With circle hooks, come tight and let the fish load the rod; the hook turns into the corner of the jaw as the fish turns away. Striking on a slack line is how you pull the bait out of its mouth at the moment it commits.

If the fish ignores the bait and stays on the teaser, change one thing: drop the bait further back, or change its angle by turning the boat slightly. Repeating the same drop-back at the same distance teaches the fish that the bait is not food. Two failed attempts is usually the point to clear the teaser and let the fish commit to the bait alone.

What the rules say about hookless teasers

A teaser may be fished without hooks, and in most billfish tournaments that is exactly how dredges are run. The fish must be hooked in the mouth on the bait or lure it takes, rather than foul-hooked on the teaser. IGFA's international angling rules are built around that distinction, and a fish that is snagged by a teaser does not count as a legal catch.

For Atlantic billfish, the release rules sit on top of the tackle rules. NOAA's HMS regulations require billfish that are not being kept to be released immediately, without removing the fish from the water, and ICCAT's rebuilding programme for blue and white marlin sets the minimum retention sizes that apply where retention is allowed at all.

The hook on the switch bait is a rule, not a preference. In Atlantic HMS tournaments, NOAA's 2025 compliance guide requires a non-offset circle hook when billfish are targeted with natural bait or a natural and artificial combination, and allows J-hooks only on fully artificial bait. A dredge of plastic does not exempt the natural bait behind it, so a switch rig built around a ballyhoo or a mackerel is a circle-hook rig by definition.

That combination decides how you rig. If you are fishing for release, crimp the teaser connections so nothing can hook a fish, run the dredge on its own dedicated line, and keep a dehooker and line cutter at the transom. The gear that makes the switch easy is the same gear that makes the release clean.

Check the tournament rules before you leave the dock. Some events restrict the number of teasers, some require natural baits to be rigged on circle hooks, and some count a fish as released only if the leader is touched or the hook is removed. Those rules change the rig, not just the paperwork.

When does a teaser hurt you?

The first case is a fish that will not leave the teaser. Blue marlin in particular can follow a dredge for minutes, and every drop-back that fails makes the fish more focused on the frame. Clear the teaser, turn away, and come back with a bait-only spread rather than repeating the same move.

The second is too much dredge for the conditions. Two dredges plus a full spread in a 15 kt crosswind is a handling problem: the boat cannot turn without crossing lines, and a fish that eats on the inside bait drags the dredge into the spread. In those conditions one dredge and four baits out-fishes two dredges and six.

The third is a dredge that is fishing too deep for the species. White marlin and sailfish work high in the column, often within 10 ft of the surface, while blue marlin will come from deeper. If the dredge is at 25 ft and the baits are at 8 ft, the fish rises past the bait to the dredge and never sees the hook.

The fourth is fouling. Weed, jellyfish and sargassum collect on the frame and turn a baitball into a dragging mass. Check the dredge every 20-30 minutes, and keep a second frame rigged so a fouled one can be swapped instead of cleaned on the troll. A clean dredge at the right depth beats a bigger one that is dragging weed.

The fifth is a dredge that is fighting the sea. A big frame in a head sea or a strong cross-current drags harder, loads the boat and slows the spread, and the fish may be seeing a baitball moving at an unnatural angle. If the dredge is pulling the stern around, it is too big for the day. Drop to one frame or a smaller one before you change anything else.

The last is the assumption that more teasers make more fish. A single clean dredge and a well-placed bait catch fish because the fish can see them and reach them. Three dredges and a wall of teasers catch fish because they are dragged through a lot of water, and they cost you the ability to turn, to see a strike, and to release a fish cleanly.

Short version

  • A dredge is a herding tool: 10-20 ft down, 30-50 ft back, with the hooked bait 20-40 ft behind it.
  • Switch by free-spooling the bait back 50-100 ft with the boat in gear, then come tight without striking.
  • Use hookless teasers, keep a dehooker and cutter at the transom, and check tournament rules before deploying.

Sources

  1. Sailfish: State's Saltwater Fish Offers On-the-Water Excitement — Florida Fish and Wildlife Conservation Commission · T1
  2. HMS Compliance Guide: Recreational Fishing Guide for Complying with the Atlantic Tunas, Swordfish, Shark, and Billfish Regulations — NOAA Fisheries · T1
  3. IGFA International Angling Rules — International Game Fish Association · T2
  4. Teaser Tactics of Tournament Experts — Sport Fishing Magazine · T3
  5. How to Rig a Dredge for Billfish Trolling — Tackle Room · T3
Set Trolling Spread Geometry Before Lures
An outrigger clip set for a skirt will drop a live bait
Kite fishing: 8-15 kt of wind and a 3 kg release clip